molle mic clip 3d models

Mic clip replacment for a friend. ... 30% infill & supports PLA

Used components: - mic from headset with diameter 10mm - audio cable (2 wire) 3mm width - 3.5mm audio jack - paper clip 19mm Print it vertical with mic cap down. Support and brim is not needed just one or 2 skirt lines. I placed 1 layer (0.2mm)...

CB Radio Mic ClipReplacement part for marine radio.Designed on PTC creo. ...prt, stp & stl files inlcuded.

This attachment lets you connect your mic directly to your molle visor. By routing the cable back over the rearview mirror and down, you keep it out of the way while off-roading. This setup is super useful when navigating rough terrain. To ensure...

This will allow you to attach your mic to your molle visor. I run the cable back over the rear view mirror and down, so it stays out of the way. This is very helpful when off roading. If you want to leave it attached, I suggest using PETG so it can...

Molle Clip Just add 3mm Bungie cord Can be used to hold various objects I design it for use with my airsoft vest.

... latch securely holds the microphone in position. Before attaching the disc to your mic, ensure its height aligns with specifications. For mics up to 4mm (Yaesu, Alinco) models, use the low-disc version; for 5-8mm mics, opt for the standard design.

Simple clip for MOLLE webbing. ...I designed this to make compression straps for my backpack.</p> <p>For compression straps project, I used this buckle: <a...

Sennheiser 421 mic clip designe made for use in standart mic clips Enjoy JMC 3D Team

Sennheiser 421 mic clip designe made for use in standart mic clips Enjoy JMC 3D Team

JMC 3D MIC CLIP FOR THE SENNHEISER 421 MIC CLIP FOR USING WITH STANDART MIC CLIP EASY FOR MAKE YOU NEED IT, WE DESIGNED

Mic Clip for the Royer R10 and Shure 57

Had to reverse engineer a mic clip for cables.

CB Radio Mic Clip. ... Replacement part for marine radio mic clip. ... Included prt and stp if anyone wants to customize it for their own purposes.

This is a camera mic clip hopefully should be able to support the mic if not then this is still a work in progress.

This Mic clip is designed to hold a generic SM58-sized mic. ...I printed it in a vertical orientation, with the wider end facing up.

Mic Stand Cable Clip secures the cable to the small portion of a mic stand. ... Effectively attaches to 15mm diameter tubing often found in the upper section or boom of various mic stands.

This is a plate that can attach to a mic clip to allow you to mount other things to a mic stand. ... The clip I started with is for a Shure Wireless SM58.

55° Fredman Mic Clip.These used to be 45° but it turns out that 55° gives better results.

Bought a mic for my DSLR but was disappointed the clip didn't rotate to clip vertically. I printed an adapter. ...Quick print, maybe 20 minutes.

This is a small clamp that clips onto the rim of a violin, providing a surface to safely attach a lapel mic onto.

This is a small clip to contain the cable clip on the Beacn mic. My mic orientation just happens to be less then optimal so when I adjust the position, the cables often pop out of the slots. ... This keeps the cables contained and keeps pressure on...

... fastening systems. ...This clip is designed to hold your mic in place with ease, while also providing a rugged and durable construction thanks to its flexible material. ...However, additional support may be necessary to ensure optimal performance.

* Bendable design * 19mm opening * 1mm extrusion on the bottom which clips into the groove on the microphone, locking it in place * Front face chamfered for easier insertion * Screws onto the base of a regular mic clip. Pictures are PLA printed...

It comes with a red clip that allows the mic to be attached to the flash slot of the DSLR camera, allowing easy recording while moving about. I broke that clip while removing the mic from it. These are 2 different kinds of clips that I designed to...

The mic clip stl replaces the belt clip, making use of the existing screws. The clip fits the holder (which is a remix of https://www.thingiverse.com/thing:661898. I mounted the holder using double-sided Gorilla tape, which seems to be working ok. ... ...

This is a Mic Clip for a wireless Microphone designed for the Sennheiser EW series. this Clip is designed as a prosthetic to be strapped to a wrist or arm. ... I recommend using a flexible PLA printed at the standard temps, adjust the infill for...

... Thingiverse. Thank you ThingWizard! I added on the SM57 clip which is sized to allow both mics to be flush at the business end for grill cloth mic placement. I also made the hole for the mount the same size as a standard SM57 pivot screw. ...Enjoy!

I Designed this clip in Fusion360 to protect my studio mic cable from getting damaged. Print Settings are as follows: Printer: Rostock Rafts: None, no need for them! Supports: Absolutely none, keeping it simple is the way to go. Resolution: Set at...

Remix of https://www.thingiverse.com/thing:4673422 Made the neck of the mic holder between the clip and the dovetail thicker and sloped to allow a stronger print and without supports. Get the matching clip from the original thingiverse file. ...