moen faucet hose adapter 3d models
151679 3d models found related to moen faucet hose adapter.thingiverse
This is an adapter that goes between my Moen gooseneck faucet and a garden hose, so I can connect my sink to my fish tank syphon / refill adapter. The Moen faucet is some weird custom thread setup so I ended up having to put calipers on it to get...
thingiverse
We have a big fancy Moen Pull down faucet and none of the included adapters connected to the hose where the sprayhead/fauct unscrews. Thanks to the vigilance of some home brewing forums I found that the connector is and m16x1.5 thread. I was able to...
prusaprinters
We have a big fancy Moen Pull down faucet and none of the included adapters connected to the hose where the sprayhead/fauct unscrews. Thanks to the vigilance of some home brewing forums I found that the connector is and m16x1.5 thread. I was able to...
thingiverse
A thread adapter to fit current model Moen kitchen faucet spray nozzles, at least the ones with 15+mm thread o.d. by 1.5mm pitch. The unthreaded end is 3/8" o.d. so that I can slip a piece of 3/8 vinyl hose over it, and from there over my 3/8" o.d.
thingiverse
This set of spare components is designed to repair faulty Moen faucet handle adaptors on bathroom sinks.
thingiverse
... it needs to be, and the layers make an ideal breeding ground for bacteria. I may seal it with epoxy, or just give it a good spritz every now and then. I am not exactly sure what model of faucet I have, but it appears identical to the Moen 7900.
prusaprinters
But we just got a new moen bathroom faucet and it didn't fit. The threads on the moen seemed to be about 21mm wide and 1.5mm pitch. The hose part is about 24.5mm wide and has a 1"/27 or 0.94mm pitch. I printed it in this orientation. The sink is a...
thingiverse
... and seems to work well. Be sure to put those rubber washers in so you don't get leaks. My particular faucet is: MOEN Noell Single-Handle Standard Kitchen Faucet with Side Sprayer in Spot Resist Stainless Model # 87506SRS Sold in Home Depot
thingiverse
I installed my moms Moen kitchen faucet about 14 months ago and I told her to hold on to the tool they provide. When the faucet cartridge leaked I needed to remove the faucet (didn't need to but did anyway for trouble shooting). She did not hold on...
thingiverse
This cap fits a Moen one-handle pull down kitchen faucet, model S728 series. One of the clips finally broke off the cap on the kitchen faucet, requiring a replacement. Since this faucet is no longer in production, I chose to design and print one. ...
thingiverse
Simple hook that attaches to existing hardware for a MOEN shower faucet. The screws on my shower faucet are 2 inches apart and are offset by 45 degrees. I haven't done a stress test to see how much weight it can hold. ...Right now it can support my...
thingiverse
Needed a replacement Moen install tool, to remove my Moen faucet. This took the place of Moen part 118305. I uploaded the OpenSCAD file as well, which will let you customize it to your own size or for some other project. You can comment out a few...
thingiverse
This is a remake of the internal part for Moen faucet, originally by ksaathoff. I changed the internal and external dimensions to account for .5mm expansion of extruded filament. ...The original part was just too tight to use, both with placing onto...
thingiverse
My faucet says MOEN 4600 27000 54000 74000 84000 SERIES on the base of it where it mounts to the top of the countertop. It has a 0.325" spacing from one flat to the other that allow it to turn the brass shaft and accepts a 0.375" diameter brass...
thingiverse
Replaces inner aerator for Moen bathroom faucet. It actually work well, not like the others I printed here and tried. Assemble the InnerRibs between the ribs in the Housing then place the Cap on, flush side up. Place into the original metal screw on...
thingiverse
I needed a quick adapter for my coil from a 20cm wide faucet head to a 7mm hose Figured someone else might need something similar one day so, enjoy :)
thingiverse
... faucet adapter for substituting the one that got stuck inside a filter. ... Had to reverse engineer this connector, which sits between the faucet and the hose that is used for the shower, since I couldn't use the original made of metal anymore =/. ...
thingiverse
This is a removable Faucet to Hose Adapter. It is designed for my Aquarium Hose (6mm inner diameter). You need a sealing ring with a outer diameter of 20mm and a thickness of 1,5mm. ...You can glue the sealing ring to the adapter.
thingiverse
I had buyers remorse after I bought this expensive kitchen faucet. The reach of the arm was really short, and I couldn't fill anything without pulling the arm out and holding it. I wanna multitask, dangit! This extends the faucet handle 70mm...
thingiverse
This is an unobtainable part. ...These faucets are still being sold at The Home Depot so even when they're brand new you cannot get this part. ...Not even a part number on diagram (see pictures).
prusaprinters
The faucet doesn't leak anymore, and the wife finally appreciates this fine 3d printing hobby. This currently installed in my bath faucet and works great. its a little tighter maybe because I didn't calibrate the filament flow. However there is very...
thingiverse
This is an adpater that will allow you use to connect a water hose to the faucet. It can be customized for whatever project needed. For the time being it, is a work in progress. It is a pretty heavy customization of the nuts and bolts openscad. ...
thingiverse
I had seen an adapter in the net but should cost 25 €. Too expensive, I build myself. It is programmed so that you can change all important parameters. But unfortunately he is not leakproof, you have to look for a piece of rubber and make a...
thingiverse
After purchasing a Moen Pulldown Kitchen Faucet (INS10205C), I needed a new adapter to connect to my Aqueon Python Aquarium Water Changer for tank cleanings. To use this adapter, remove the faucet spray wand and connect to the hose. ... Note: This...
thingiverse
Designed a faucet adapter for my gooseneck Moen faucet. I believe it is a 1/2" thread, with this designer's 3/8" barb for a vinyl hose. Designed for use with my copper immersion chiller for wort. Works perfectly. No leaks. Remixed both source...
thingiverse
This is the adapter part for a Moen single handle kitchen faucet. After finding the local home improvement stores didn't have the part and would take a week or so to order off the internet, I scienced the shit out of it! so, print in 100%. It will...
cgtrader
Moen 5925BL Sleek One-Handle Pre-Rinse High Arc Spring Pulldown Kitchen Faucet - Matte Black GEOMETRY High quality model Real world scale (25.4 x 13.8 x H59 cm) Centered on X,Y,Z axis Turbosmooth on/off TEXTURES 5 materials 3 texture files FILE...