mods for ender 3 v2 3d models

I recently bought an Ender 3 v2 printer as a second printer and did not plan to do any medications. Unfortunately, the cooling performance when printing PLA was less than optimal. This might be something specific to my printer. I decided to design...

... bearings, bolts or any extra part; just print it! I used a layer height of 0.2mm, an infill density of 20%, and tree supports. You'll need to print: * Two roll support for spools - Ender 3 - CLAMP * Four roll support for spools - Ender 3 - ROLL

I designed these supports to enclose my Ender 3 V2 and print ABS without the shield feature, as in one closed printer, once to print this filament we should keep de temperature a little high, to avoid warping, delamination and cracks. In my tests, at...

A surface to attach your GoPro mount that you can slide through Ender 3's aluminum profile. ... To make a fast print for something for practical use only I used a 0.8 mm nozzle and printed it with a 0.2 mm layer height.

Simple Bulb base for very good light over the circuit board. ... I did not want to use led strips since I had 2 bulb holders and a switch lying around. designed to fit over top bar on ends 3 v2 (20mm)

Minimalist, simple and efficient with a very limited budget to be able to print almost any filament while keeping, at most, the original characteristics of the Ender 3 link of the video for the assembly with explanations and additional links:...

Should fit the Ender 3 V2 using two screws and the included clip, however this has been designed for the Micro-Swiss hotend and may or may not cool or fit a stock Creality one properly. This duct is modular, and can be assembled using only one...

The latest revision of my CAIMEO Fan Duct for the Ender 3 is now live. This upgrade takes a significant leap forward with several key improvements over its predecessor. The most notable change is the relocation of the fan to the rear, allowing for...

This is a pen plotter attachment for any printers that use the Ender 3 e plate. Loosen the bolt that is holding the roller, slide the bracket on to the plate and tighten. Simple mechanism, no explanation needed. Offsets: X -44.0 Y +0.5 (Not really...

I remixed the top mounting hole to align with the hole in the Ender V2 X gantry plate. Use the shorter, silver M3 screws found when you take apart the stock fan shroud, not the one that is normally used to hold the stock fan shroud. This is my first...

I remixed the top mounting hole to align with the hole in the Ender V2 X gantry plate. Use the shorter, silver M3 screws found when you take apart the stock fan shroud, not the one that is normally used to hold the stock fan shroud. This is my...

Remixed the Ender 3 Max dual z height sync spacer from scratch to fit the Ender 3V2. So basically I took the idea and made a new version to fit my needs. Used to sync the heights of your Dual Z axis. And can also be used to help set the Z axis...

I'm grateful to Blinkii from thingiverse.com for their design of thing:3178072, which I used to upgrade my Ender 3 Pro. What I was looking for was a design that would seamlessly integrate with the upgraded features of my printer. Since the Y-axis...

This is a pen plotter attachment for any printers that use the Ender 3 e plate. Loosen the bolt that is holding the roller, slide the bracket on to the plate and tighten. Simple mechanism, no explanation needed. Support: Only needed in refill holder....

I made this 60mm diameter centering cone to complement the https://cults3d.com/en/3d-model/various/support-bobine-filament-creality-ender-3 coil holder so I could use coils with a smaller centering hole.

Make your Ender 3 look Bad to the Bone with this custom knob! This is my 3rd print ever and first print I designed. ...May need supports depending on how you slice it.

Made for the Creality Ender 3 v2, but it may fit the Creality Ender 3 and other Creality printers. This is an x-axis carriage mount that works by attaching a digital depth gauge (like [this one found on...

This is a simple mounting bracket to attach a Logitech C270 to the Ender 3 X-gantry. It holds the camera at a good angle towards the bed and printing head, with the tilt being adjustable. The camera and bracket itself are attached using a clamping...

This is a simple mounting bracket to attach a Logitech C270 to the Ender 3 X-gantry. It holds the camera at a good angle towards the bed and printing head, with the tilt being adjustable. The camera and bracket itself are attached using a clamping...

I was fed up with the dramas I had experienced updating firmware on my Ender 3, and as a result, I was left with a dead machine. So I ordered Biqu SKR1.3, TFT35, and 2009 stepper motors to get back into action. The screen arrived first, but...

* **v2**: Improved stability and tolerances * Da Duct v2: A bit more clearance so the fans slide in easier * Da Touch Mount v2: The old version broke at the mounting screws since there was only one layer holding everything together. The mount is also...

It is just a tool holder for the Ender series but with a sliding mount instead of press-fit, and some SD/microSD card slots.Minimal supports needed, just for the sliders.

For the fan I used an noctua NF-A9x14 PWM but other 92mm fans should fit as well. The part is designed to print with a 0.6mm nozzle. Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: NoResolution: 300 Infill: 38 Filament:...

... near by and hadn't found anything I liked, so started learning how to use Fusion360 and designed this. ...It slides into the rails on the bottom of different Ender 3 models. ...I found it printed best from a corner, with a small raft and supports.

I only used this for tuning input shaper, then removed the mount.This model uses the space from here: BLTouch Spacer/Screw Cover for Ender 3 Pro by onpdm - ThingiverseI don't have a photo of it mounted, I'd removed it and started a new print by the...

Cover for the Ender 3V2 Display. I recommend printing the frame in an upright position with supports enabled in order to make the snap fit work better. ... After assembling you can mount it with double sided tape to the screen as shown in the picture ...

... on the back. PLA seems to work best, as it is stiffer and this part wont see heat. You might also find printing the slide at 101% size makes it fit REAL nice.This is a remix of “Ender 3 Adjustable Endstop (3 and 3 Pro)” on thingiverse by Mach_Zero

Case for Ender 3 / 3 Pro / 3 V2 in the "Minimal" style. ...Included is a file with a case cover with holes for better cooling and reduced fan noise.

This is a remix of https://www.thingiverse.com/thing:5179838This remix takes the mount the fits the Ender3 V2 hotend shroud and modifies it to fit a Mitutoyo 2046 dial indicator. ...The mount is a direct replacement for the rear cover of the dial.It...

Please use support when printing part 1,2,3. ... also use raft when using PETG filament for avoid elephant foot