mods for ender 3 v2 3d models

BLTouch bracket for Ender 3 V2 This is a revisited version from an existing file created by Moe Sabri on a different portal. BltouchMount_v1 - Horizontal bracket thickness: 4mm - The cable holder is quite close to the main body. - This can...

This is a remix of the Voron Sexbolt Z endstop for use on my Ender 3 v2. This fits the [hartk Z endstop board](https://www.amazon.com/gp/product/B09YGGQ8GZ/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1). I used 2x M4x6 screws and T-Nuts to secure...

Seems the Ender 3 V2 rubber feet are slightly taller. This is one of two pieces, for other piece check out the original design - https://www.thingiverse.com/thing:3541279, damper_feet_4040_-_A_-_rubber.stl is the one used. ... Here are some great...

FOR ENDER 3 V2 ONLY - See the last image for the compatible hot end cover I had purchased some buck converters from amazon to allow me to use a 12 volt fan for the hot end (the stock fan is 24 volts). I was not content with the converter hanging...

My printer is a Creatly Ender 3 v2, so, I can't tell you if it works in other model, but, the side supports must be standard so, there is a chance to work on other Ender printers. Please let me know if I can improve the design. ... To improve the...

Minimal size case to install a raspberry pi into an ender 3 v2. ... The clips have no margin, so you will have to move each side in and out a couple times before fully inserting it, otherwise it can get stuck x)

This is an adapter to be used with the original spool holder of Ender 3 V2. I have limited space above the 3D printer where the original holder is fixed. So, this thing could be used together original holder over a table. ...I'm using beside de...

... haven’t printed yet if anyone wants to print and let me know i can adjust. ...`It should fit the screws that lock in the slots. I took the idea from this https://www.thingiverse.com/thing:2757810 design added it to this to fit the ender 3 v2. ...

I combined this with a mount to attach it to my side rails on my Ender 3 v2. ... I installed it on the left side of my printer, you'll need to remove the 2 fronts (LARGE) screws and 1 screw at the bottom.

This is a replica of the control knob on the Creality Ender 3 V2. I basically just measured the original knob and recreated it, tweaked a few things here and there. I did this to make my printer more... colour co-ordinated :) Hope you guys enjoy! ...

**************************************************************************************************************** This is a side-mounted spool holder with a bearing roll for the Creality Ender 3 V2. Inspired by...

https://www.thingiverse.com/thing:5236927** The stepper motors on the Creality Ender 3 v2 3D printer are very quiet, which makes the cooling fans the loudest parts of the machine. If the user replaces the included fans with quieter alternatives, the...

Improved Filament motion sensor for Ender 3 V2. Not only detects a filament runout, it also detects a nozzle clog and pauses the print safely. Intended for use with klipper. ... ##Used Parts [M3 20mm...

Just a base to use the dual 5015 frame on an ender 3 v2. READ THIS BEFORE DOWNLOADING DUCT BASE 2: Duct base 2 has oversized mounting holes so that M3 threaded inserts can be installed. If you print this and do not install inserts, the 4 holes...

Dial Gauge Holder for Ender 3 (v2 - added back support and no knob needed) This is a simple holder for a dial gauge (mechanical comparator) to install directly on the Ender 3 fan cover using its screws. No modification needed. **Please Post Your...

The roller is angled to better support filament spools mounted slightly to the rear such as the deault Ender 3 v2 top mounting arm or my (more compact) rear mounted spool (https://www.thingiverse.com/thing:5330574). The angled roller also keeps the...

Just what we need yet another d__n tool holder to attach to the Ender 3 V2.  I decided I needed my very own tool holder for all the stuff I wanted to have at hand. I made it in lots of bits for a couple of reasons. I hate having to clean supports off...

I modified Chris's test to fit the Ender 3 V2. It is designed to work within the 235x235 bed and prints at 220x220 so it stays away from any clips that are used to hold the bed in place. Edit: You may need center the model and then shrink to 99%...

Simple mount for a Wyze V2 Camera to an Ender 3 I used longer SS socket head capscrews to mount into the existing holes. Doing this allowed me to add bosses and have a strong mounting area. If you want to use the existing screws you may need to...

The hotend cover is designed to re-use the existing Ender 3 V2 fans and the adaptor plate is compatible with the Creality BL-Touch ABL kit.The magnets used are round 6mm x 3mm. A small drop of CA glue is all that is required to install them into the...

Screw template for standard hotend bracket for Ender3 V2.

Credit to BoothyBoothy for allowing me to use a couple parts from his Manta MK2 For Ender 3 V1/V2 Design : https://www.thingiverse.com/thing:4943125 I really suggest checking out his other designs! Things you need: 20 x 5mm OD by 5mm L M3 Heat...

... any Ender machine and non other brands that have the same/similar rail. Note: For best finish print like in the pictures with supports Note2: if you're struggling to insert tool holder, remove the rubber cap on the end of the rails and rotate it.

Modified original design to allow the model to lay flat on the bed of the Ender 3 V2 so it can be printed without supports. Also added Wii logo to front of the stand. ... Filament: 1.75 PLA Glass Blue Inland Layer Height: 0.2mm Wall Thickness: 0.8mm...

Modified original design to allow the model to lay flat on the bed of the Ender 3 V2 so it can be printed without supports. Also added Wii logo to front of the stand. ... Filament: 1.75 PLA Glass Blue Inland Layer Height: 0.2mm Wall Thickness:...

These feet are designed to fit perfectly under the default rubber feet that come on the Ender 3 v2. You'll need to print 4 of them to completely elevate the printer. The elevation is roughly 1.8 inches, which is more than enough space to increase...

Ender 3 V2 sensor mount for the TH3D EZABL and EZABL Pro 18mm sensors. Can also be used with TH3D's adapter rings for the 12mm sensor.Since it's outside of the fan shroud entirely, it won't be exposed to much heat. PLA, PETG, ABS, they'll all work...

Items prepared for the standard Ender 3 v2 printer. If the printer has been modified (Dual Drive, Higher Frame,…) you may need to adjust selected items. For example, in the "additional" file, there are elements that adapt the project to "horizontal...

This is a 3D Printer Head Made For The Diamond Hotend.Credit to BoothyBoothy for allowing me to use a couple parts from his Manta MK2 For Ender 3 V1/V2 Design : https://www.thingiverse.com/thing:4943125I really suggest checking out his other...

I recently bought an Ender 3 v2 printer as a second printer and did not plan to do any medications. Unfortunately, the cooling performance when printing PLA was less than optimal. This might be something specific to my printer. I decided to design a...