mods for ender 3 v2 3d models

- M4 x 8mm capscrew and M4 T-nut to mount to the Ender’s frame (I used the ones from the redundant Z stop after installing the BL-Touch); you’ll probably have something sitting around, if not try this thing: https://www.thingiverse.com/thing:3050607...

Slightly shorter spool holder (original is 90 mm) for your ender 3. Uses the original locking nut that came with your printer. You will need 3 x 689RS bearings (9x17x5) in addition, the rest is printed. ...Print large parts with 10 % infill and do a...

GoPro compatible mounting plate compatible with ender 3 V2 series and ender 3 S1 series 3d printers. ... use M5*25 hex head bolts and nuts to attach the GoPro mount make sure to have the front of the mount flat on the print bed as seen in the...

A remix of Jack1961's Filament Guide and Runout Sensor Bracket: https://www.thingiverse.com/thing:3450311 This bracket fits an Ender 3 (standard, Pro or V2) and attaches using the existing screws on the Extruder assembly that connect it to the Z-Axis...

Timelapse remote shutter clicker for Ender 3 v2, GoPro and Armte-001 remote clicker. This helps you create beautiful timelapses without the need of coding and other complex methods. TUTORIAL GUIDE: https://www.youtube.com/watch?v=aAh2R8ptp4M Even...

Timelapse remote shutter clicker for Ender 3 v2, GoPro and Armte-001 remote clicker. This helps you create beautiful timelapses without the need of coding and other complex methods. TUTORIAL GUIDE: youtube.com/watch?v=aAh2R8ptp4M   Even though it was...

Shroud and Linear rail mount for Ender 3 v2. Eliminates stock aluminum hotend mount, use MGN12H linear rail. I ordered a honey badger rails from Fabreeko, great for price!Mounts to linear rail and uses a clamp in back to hold belt. Hotend is a...

By using the original spool holder of the Ender 3 V2, the filament spool keeps swinging back and forth while printing.  It is sometimes annoying as it makes some noise.  Also, a more secure way for hanging the filament spool is needed to...

* To add USB power ports to my Ender 3 v2 for my Raspberry Pi running Octoprint, and to power the USB LEDs surrounding the printer. The How: * Print each section as needed, and connect with the clips only, or secure with your preferred...

This is a remix of a vital part of Stilwell's power switch mod (https://www.thingiverse.com/thing:4864993) - the actual relocated switch mount on the front end of the right base extrusion on the printer. Why? Because ... apparently Creality uses...

Ugly.• Only 35g to reach that sweet print speed you crave.• Ugly-but-Light is inspired by Satsana and mini Satsana, but built from zero in an ugly way.• Compact, just a few millimeters wider than the stock cooler.• 4010/4020 fan for hotend,5015 fan...

It fits for the stock setup of an Ender 3 V2. Needs two M3 threaded inserts (4.6 x 5.7mm) to attach the bucket to the holder. Holder can be mounted to Z-Axis using M3 T-nuts and screws. Mount it at the lowest possible point to prevent issues...

This design was intended to be plug&play with the stock extruder on my Ender 3 v2. Part of my goal was to not have to disassemble anything. In particular, I did not want to take the extruder apart as it prints perfectly right now. You do need to...

Required : a Dremel to cut the square hole a drill to make the four M4 holes a soldering iron x4 screws BHC or CHC M4x30 (Mesure the exact length and cut the end for a better finished before to screw the fan) x4 scews BHC M4x6 I am not...

The original model hit the top rail of my Ender 3 V2 for whatever reason. I did like the model, so I extended the shaft and made a few other changes:  Increased shaft length by 5 mmChanged fillet on top edge to a fillet & chamfer combination...

Hello, I recently modeled and tested a tab to make a creality Ender 3 v2 a direct drive.5 printer that should also work on other printers from creality but this has yet to be confirmed) This last one allows to print all kind of filaments including...

This custom adapter/mount has been made for the Ender 3 V2.However it may also work on other printers with a similar gantry plate.The mount was made as a way of converting from a bowden setup to direct drive in the cheapest way possible while also...

... is this one: https://www.thingiverse.com/thing:3391094 I use the Creality Spider v3 on my v2 neo. Here's the adapter I'm using, with the same m3 insets from above. https://www.printables.com/model/364385-ender-3-neo-spider-adapter-heat-set-inserts

It snaps onto the Z-axis limit switch bracket of the Ender 3 without requiring any additional tools or parts, unless you want to do so. The Thing includes two versions of the arm: - A slide-on camera arm that slides and snaps into place - A...

My take on a fan cover for the Ender 3 v2 power supply (MeanWell LRS-350-24) which allows mounting of an 80mm fan on the outside. Additionally I added an easily removable terminal cover, so it's not possible to touch the mains and 24V terminals when...

The filament hole is about 10mm higher than the stock one. Compact bearing guide and runout sensor made to fit within Creality Support Rods, uses: 1- KW12-3 Roller Lever Arm Micro Limit Switch 1- 608 Bearing 2- bearing spacers from this thing:...

Remove the two retaining screws from the 3 pin power inlet, this will give access to the adjacent switch 3. By manoeuvring a small screwdriver through the hole where the power inlet was removed you should be able to compress the retaining clips on...

I designed this to easily hold the PS3 Eye camera on the Ender 3 V2 without any extra hardware and while being easy to remove. This attaches to the X-axis of the printer. You just have to slide it on! It has room to pivot in case you want to...

This is just a remix from https://www.thingiverse.com/thing:4401649 The Mandalorian Helmet UPDATED by TheBrokenNerd83 May 27, 2020 I just used fusion360 to split the helmet into 5 pieces to be printed in the Ender 3 V2 Neo I added a sizing ring (the...

I made this to protect the lead screw on my Ender 3 V2 from being damaged while preforming upgrades and maintenance, as well as protect it during general use. This stabilizer provides no bonuses while printing, it merely protects the lead screw...

I loved the OG design(s), but they were not the best fitting when printed with my Ender 3 V2. Thus, I redesigned all the pieces to fit just right! Thank you for stopping by and Merry Christmas! :) PS: I highly recommend the 3MF prints on the Prusa...

just print mirrored for the other side part list for mod:short M2.5 knurled nuts:  https://www.amazon.com/dp/B08GWKW1K7tiny slide toggle: https://www.amazon.com/gp/product/B007QAJUUS4mm or slimmer li-ion batteryreset button (the one corne...

Turn power off and unplug printer Remove the two retaining screws from the 3 pin power inlet, this will give access to the adjacent switch By manoeuvring a small screwdriver through the hole where the power inlet was removed you should be able to...

A front-mounting screen bracket for the Ender 3. I have my printer in a narrow alcove, and by front-mounting the screen I can save a little overall width. The screen is now inside the profile of the rest of the printer. ...The drawer still has just...

As my fan was producing annoying hiss sound I also used a small fan duct: https://www.thingiverse.com/thing:4050647 Also camera ribbon cables can reach eaisly: https://www.thingiverse.com/thing:4834763 Which I used with modified case to fit Arducam...