modem rack mount 3d models

so i made a tray that works with @russross raspberry pi 4 1u rack-mount bracket project. ... https://www.thingiverse.com/thing:4125055 this macmini tray module is designed to replace 3 of the 6 pi modules that would make up 1u on the rack. macmini...

The 1U rack is a Rising Electronics 1U 19x6 vented cantilever shelf which can be found on amazon for aprox $19 2. The #4-40 flush nuts can be found at c4labs under "Upgrades and add ons" for aprox $4 for 20. Ive included a DXF and OBJ files in...

... etc. "Raspberry Pi 4 Case for 1U server rack" "Top uses M2.5x5 screws" "Bottom holes are made for M2.5x8 screws from below into posts above Raspberry Pi." "Note: Remove SD card prior to installing RaspberryPi to prevent possible SD card damage."

Modified to make pocket deeper to make room for rack mount screw behind mic stud. ... Remixed from CB/Ham Radio Mic Holder Remix II: https://www.printables.com/model/143075-cbham-radio-mic-holder-remix-ii I printed this to hang my Retevis Mic: Ham...

Case for dsTNC Modem. ...For more details on the dsTNC Modem, check out http://sp9uob.verox.pl/dstncv2.html in English.

simple cap + screw. ...fits in 22 mm ID wire rack legs.

This will allow you to rack mount your SB500H into a 19" rack that is 12.25" deep similar to the Gator 3U that I use. I know it seems counter-intuitive, but I originally had a larger 2U Ampeg head in there until it died out. I also do lots of gigs...

I'm starting to organize all my non-rack-sized networking gear on the side of my rack, clearing space for newer rack-sized equipment. This vertically secures an SG-1000 to any standard server rack. I've successfully used it on the side, and it should...

I took the amazing 19inch Rack from boxes.py (https://www.festi.info/boxes.py/Rack19Box?language=en) and made a pi-rack-mount out of it. On my pictures i have space for one pi3 and three pi4's. In the svg there is my version, a version with only...

I took the amazing 19inch Rack from boxes.py (https://www.festi.info/boxes.py/Rack19Box?language=en) and made a pi-rack-mount out of it. On my pictures i have space for one pi3 and three pi4's. In the svg there is my version, a version with only...

I took the amazing 19inch Rack from boxes.py (https://www.festi.info/boxes.py/Rack19Box?language=en) and made a pi-rack-mount out of it. On my pictures i have space for one pi3 and three pi4's. In the svg there is my version, a version with only...

High-Speed Modem Connectivity Module For enhanced wireless coverage and a reliable internet connection.

... At the helm of LANcity was Rouzbeh Yassini, an Iranian-American engineer who drove innovation. Nortel later acquired LANcity, ultimately shedding its cable modem division to form ARRIS, which remains a leading manufacturer of cable modems today.

Little clip to hide the bright led on the front of the Ziggo modem.

It is a type c USB Modem which is used for internet connectivity

Cable modem users can now receive basic assistance for their PACE C6500 device.

Comcast modem shelf slides into place smoothly. ...The two-part system assembles quickly and easily.

A CubeSat employs radio modem technology to facilitate communication and data transmission.

Spice rack for wall mountDesign with holes to print with less filament:https://www.thingiverse.com/thing:6472082

20mm wide headphone hook. ...Countersunk holes for 10-32 screws and spacing for standard rack units (44.5mm / RU).

A bespoke rack mount case is being designed specifically for Oscars' pidp8 project, available online at http://obsolescence.wixsite.com/obsolescence/pidp-8. This is an ongoing work in progress. The case is crafted from 3mm red and 6mm green MDF...

80mm fan based fan mount (and optional shroud) for Surfboard SBG6580 (and possibly other) cable modems is built. Heat kills any electronics and I was uncomfortable with my shiny new cable modem running as hot as it does, non-stop day and night. A...

A simple 19" rack mountable case for a 4 port QC3.0 board : https://amzn.to/3DWd83l

This is a remix of the pliers rack to allow them to be screwed to a wall or riveted to 1/4" pegboard.

the soap rack allways had no got place to put, so I designed a holder for it to be put on the opener of the sink.

I create a custom bracket that allows easy attachment of the Cygolite HotShot 2W to the Topeak MTX bike rack. Just download this design, print it out, and experience a satisfying snap as the light clicks into place. ...For added stability, I recommend...

The ear is designed for attaching electronics to a rack and suitable for devices requiring one space. ...It features a reinforcing rib along its inner support, created using Tinkercad.

19" Rack frame: • 19" Rack Rahmen 2HE: https://www.musicstore.de/de_DE/EUR/DAP-Audio-2-HE-Rackblende-f-Modulsystem-10-Segmente/art-PAH0017160-000;pgid=SFDgeVCa1RlSRpaDRXt2K1900000oFRYW4Oi The STL File offers the Frame for 7mm thick HDDs. ...The...

I remixed this element to fit a HDD in a rack. ...I also added some holes in the top of the part to fit another element with nut inserts, in my case a relays board.

Holder to make your own case or pannier compatible with the KLICKfix luggage rack adapter https://www.amazon.fr/gp/product/B001VS0AHS/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1