models with glasses

The indent with the slots are for holding the trigger button.BaseGlue the servo holders and rotator in place. When the glue has dried you can screw the larger servo in place. When you put this on the axle on the electronics box you can add the wire...

you can attach these with your M5x8 bolts and T-nuts. I put 2 holes on the backs/Side/Top but honestly that's probably overkill. I have mine installed and it doesn't move at all when all 6 are in. Once you have your Controls installed, I would...

That version of the case requires no additional hardware; the lid will just press on and depending on printer precision, hold with friction. Post-Printing The case Bottom has built-in support on the extrusion clip. Carefully remove this support...

Also change the Processor to ATmega328P (old bootloader)You will also need to select the correct port, Once you plug in the Arduino with the USB cable the new port should appear as one of the options, select that one.After that is done you should be...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options:...

https://youtu.be/99Qh1oR2A6A See all the details and how to assemble in this video: https://youtu.be/eCfw9fd0mHg Source CAD: https://cad.onshape.com/documents/5509608f682224235855a810/w/6c2a90d7701f2b3540e103d9/e/a6666422824314d6fd1547db John Toebes...

It is also cool to have dimmer remote on the lamp, use colorful LED strip or connect it with voice...

With thanks to Dickson Sham for the comprehensive tutorials, we can enhance our knowledge and skills. Credit goes to Dickson Sham for the insightful tutorials. Dickson Sham's tutorials are the source of credit for our learning journey. Let's...

Customized version of http://www.thingiverse.com/thing:287025 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options:...

Less support is needed for the vertical orientation, but I've found that the horizontal position, with support, gives better results. In horizontal orientation, the top of the round adapter is narrow, so the last section prints poorly. In this case,...

You will also need 2 m2 heat set inserts and and 8 short M3 inserts for the replacement Y max endstop target To install, bolt the drill guide to the idler plate with it and the attached hardware removed from your Taz. Drill the hole and clean any...

**The MorningRope will help with all of that. It is a smart curtain opener that automatically opens and closes your curtains for you.** The device is completely hidden so it looks great in any home, and uses off-the-shelf curtains that can be...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: ...

(boom-tss) Ill be adding a version the brings the top of the battery even with the top of the soldering iron, making it even better balanced in the hand. I will also be addind a version for the Pinecil, whenever mine arrives and I get some time. It...

See als my pictogram collections: Emergency Symbol collection: https://www.thingiverse.com/thing:4830734 Fire Symbol collection: https://www.thingiverse.com/thing:4830768 Mandatory Symbol collection: https://www.thingiverse.com/thing:4832942 Warning...

When mounted in the goggles with the irises open and the little actuator tabs at the top, they should open when the tab is moved to the outside of the goggles. Snap each eyeball in place accordingly. Be very gentle because the little fingers on the...

This M code may not work with all printers. When you auto-level your bed, the leveling probe points should all be equal distances from the edges. The center position should be exactly in the center.Notes: It is possible on some printers that X-Axis...

PTFE tube to feed the filament from the spool through the support, I used hot glue to hold in place:Create the bolt holder filament weights:Attach the two parts (airBufferBoltHolder.stl, filamentPassthrough.stl) with super glue after the filament...

Select the entire presentation by pressing Ctrl+A, then right-click on the presentation and select "Note." In the dialog box that appears, type in the following text: "This is a sample assembly." By completing these exercises, you'll gain a solid...

I ended up designing my own steer, with the intention of making it as minimalistic as possible. because those that I could find online were either too expensive, too big or required an electrical outlet, etc. This one just uses a simple regular...

Other colors will also work, but will filter the color of the LEDs.The WeMos D1 Mini is a self-contained ESP8266 board with the ESP-12F microcontroller, a 3.3v regulator and built-in USB UART. They are readily available from a variety of sources. In...

Either hard wire or use a 2.1mm jack. One of the corner covers has an opening for the cable, so make sure you identify this one and reserve it for the correct corner. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No...

Furthermore, the end would sometimes fall out, leaving me with a tangled mess. So I decided to design the super greatest ever spool for filament samples. (OK, maybe I overstated that a bit.) After all, it was just for me so I was not considering...

Could be used longer. Cover: 6pcs M3x12 (up to 25) DIN912 with or without nuts. Both variants are possible. If you prefer nuts, you have to use longer screws (ca 20 or 25 mm).</p> <p>Box: 4pcs M4x10 DIN912 + T-nuts.</p> <p>5V Step down converter:...

Various forms of round objects assistant A range of spherical figures can be found. YPE THIS AGAIN, BUT WITH A DIFFERENT WORDING: Numerous examples of globular shapes exist. assistant An assortment of round-shaped items is available. assistant...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: ...

Take this as a cool project that I wanted to share with you just for fun. ITA: Durante lo scorso inverno il mio vecchio termostato si è rotto quindi ho deciso di realizzarne uno io stesso per mettere in pratica ciò che studio all'università. Il...

In this pack you can find more Scifi machines and parts to create a void shield generator in combination with my other parts like the "smokestack" or the "Pipeline Pump Relay". If you use the "Bitz for Scifi Buildings" (1-5) you can decorate it even...

Customized version of http://www.thingiverse.com/thing:287025 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options:...

I've been using an adjustable width spool roller for quite some time now, but it's annoying when you change rolls a lot, if they are different in width.So i decided to make a roller that could fit most spools.Updates:V2 - 24 April 2021&nbsp;Generally...