models on beach

otherwise you will have a air leak. and of course you still need a spring and 2 pins to complete the mag release note: these have been tested on X7 classic and X7 phenom bodies. link to the Installation video of the T15 and TMC magfed adapter if...

________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Tinkercad link: https://www.tinkercad.com/things/7aYnpLajauz ________________________ Some of my other designs:...

Empty your shredder regularly!because if this is too full, it pulls the scraps of paper with the knives (rollers) on the outer sides back into the housing, which leads to enormous clamping forces.This may also have been the reason for the defective...

Gruß Hardy ---------------------- The normal toothed belt pulleys with their 3mm axis installed in toothed belt tensioners have bothered me for a long time on my 3D printer, often make noise and cause inaccuracies. Various times I have seen...

The board also features a high-resolution LCD display, USB connectivity, and an on-board programmer that makes it easy to load new firmware and software updates. Users can program the Rovo 1000 using OpenBuilds' own IDE or other popular development...

otherwise you will have a air leak. and of course you still need a spring and 1 pin to complete the mag release note: these have been tested on X7 classic and X7 phenom bodies. if you like to be the cover photo of this one. ...then you can send a...

There is a tile with a ramp to be used as a cross walk. Available Sets Below is a list of all the different tile sets (click the link to be taken to that set): Straight curbs -- These have a curb on only one side of the tile and represent...

There is a ramp that can be uses as a crosswalk. Available Sets Below is a list of all the different tile sets (click the link to be taken to that set): Straight curbs -- These have a curb on only one side of the tile and represent non-corners. Can...

These are clearly indicated on the drawing itself. Original Fischertechnik parts are always easier to connect with other parts, which is why they're used in this design. The necessary blocks for making a straight connection or a 180-degree connection...

The Tile_D is made to work with the 50x50 tiles from my floorpack.(https://www.thingiverse.com/thing:3895156) ________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Tinkercad...

The Z-Motor mounts have been updated inline with the Prusa R3 versions and cable management has been improved. If you have already fitted a previous version of this mod and are upgrading from the MK2.5/MK3 to the MK2.5S/MK3S version I suggest you do...

In the world of Warhammer, these miniatures take center stage as players use them to fight battles on their tabletops. Each miniature has its unique characteristics, abilities, and strengths that make it essential in the game. From charging into...

As we embark on this ongoing journey of discovery, we are reminded that humanity is a constantly evolving entity, shaped by the intricate interplay between individual and collective experiences. It is a dynamic system that defies static definitions,...

I designed it specifically for the M3D Micro, but there's no reason why it shouldn't work on other Cartesian printers too. This is by far the quickest method I've seen for calibrating backlash, as it produces empirical results in one go instead of...

It is easy to print and it is heat resistant up to 120 degrees!On the photos you can see that I printed the housing in 4 individual parts.I did that because the attempts to print in ABS and ASA of the entire housing failed and the printing was...

If you want to recreate this you'll need the following things:-yellow + transparent filament for STAR WARS logo-black (or colour you want) filament for the lamp case-on/off snap in...

You should find that the Bowden pipe from the extruder will easily pass above a pair of the cut-down sheets, or between the pair depending on the configuration you need. The display remains fully visible and accessible at all times. Bonus points: ...

________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Tinkercad link: ________________________ Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet...

existing solutions rely on the raspberry pi or the arduino, for example. The 3D Scorpio photogrammetry rig works completely without electronics and has fixed points at which the iphone 12 mini can be plugged in at different angles. I use my own...

As a result of the modifications, the factory display of Ender 3V2 uses RX0/TX0 pins, placed on the TFT port of the motherboard, for communication. It is important to note, that the published settings are not complete Marlin settings! These...

The function of keeping the plastic dry during printing is performed by this box.. Maximum coil dimensions: 210х90 Required size of the printed area of the bed: 232x218 To assemble the box you will need: M3-10 x 4 – fixing the bottom of the...

Or if you want to give names to your plants.Customize the object to show your own text: Please install OpenSCAD on your own computer and follow these in depth instructions.Alternatively, you can also use the Thingiverse customizer.Note: I originally...

I printed the white shell-parts of the case each "in one piece" on a Flsun QQ-S Pro. This worked great and so I didn't have to worry about gluing it all together. The designer of the Arduino Portal Gun used a 2.5 inch tube because he lives in the...

The dimensions of every CR10 hotend should be compatible but the default (non-"all metal") hotends are designed to be used with a bowden tube inserted deep into the cold side, which is a problem for this mod.Other mods on my Voron V0:The Ultimate...

Credits: This remix leverages the container design found here: https://www.thingiverse.com/thing:3826892 I also added a die with 0.4mm deep divots based off: https://www.thingiverse.com/thing:5170067 The coronavirus image used on the token is from a...

The longer M3 bolt is used to hold the lever on the butterfly shaft. The holes may need to be eased with a suitable drill bit.</p><p>The lever has an arrow-like shape at it's tip, which shows which direction to rotate it to open the gate.</p><p>You...

It does NOT install on Sidewinder X1.This cover is only compatible with the original BLTouch V3.1 Antclabs. The previous versions and clones (for example 3DTouch) can have different dimensions that do not allow installation.</p><p>This engine cover...

If you like my work please consider supporting me on Patreon. Become a Patron! ... Tinkercad link:https://www.tinkercad.com/things/1N8tCIhz0NM Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

The rescaled version is then loaded to Fusion360, where the base profile is extruded in negative direction -0.6 mm and the black parts inlcuding are extruded to the positive direction +0.6 mm and the red part further +0.6 on top f the black material....

Filter Insert: Once the CV-19 Guardian Respirator Adaptor is inserted into the compatible snorkel mask, a filter insert cut from a commonly available material that effectively captures airborne particles is placed on the sealing surface of the...