models of tablets

I absolutely love the design of thing:1100601, but the components are too expensive and add up close to 100 dollars. So I found this lovely design and remixed it. I added two tunnels, one that goes to the front and another that goes to the top,...

The harbors are usually 25-35 feet in depth. I store the anchor in the arm of the float tube. The legs are folded onto the main body.</p> <p>The 4 hinged legs on the bottom cap manually expanded before dropping it in the water.</p> <p>I was asked...

The RF contactless shielding wallet, protects up to 8 full sized bank cards at once from RF scanning using a thin layer of aluminium foil between top and bottom. With the optional hair bubbles for money clips and tile plate, you can securely place a...

The second version uses a certified spring that produces 5kg of pulling force, stretching and tightening the cord. More laser targets can be used, set with M3 screws for mounting position straps. Normally, this location is good after assembly and...

Small (5.25" / 133.35mm) clock and art display built with 60 RGB LEDs, controlled with an ESP8266 using the FastLED library. Fully open-source, and programmable over Wi-Fi or micro USB cable. Build your own, or buy a kit from Evil Genius Labs:...

However, you can't use 2.5-inch drives or SATA SSDs with the adapter above, that's why I created a 2.5-inch version, which fits into the 3.5-inch Drive bays of the mentioned Supermicro Servers. Note: You don't need special supermicro screws! Just...

Attention : do not tighten the screws too hard when you mount the carriage on the rail, otherwise, it can block movement, If necessary, you can use thread lock on screw. List of material : - E3dV6 hotend - 40mm fan for the hotend - Radial fan 5015...

Assembly onto your unit: Loosen the stepper side of the coupling, then the 8mm screw side. Lift Z axis up, remove coupling. While holding up in the air, put the Z BRG Shield on, with the small round nub going down to the bearing. This should be a...

Additionally, the support for the two pulleys of the Intake Manifold was updated (see https://www.thingiverse.com/thing:4214349). ... # Printing Settings 1 x SuperchargerBack: Layer Thickness: 0.15mm, Raft: No, Brim: No, Support: Yes, Infill: 20% 1 x...

Customized version of http://www.thingiverse.com/thing:270289 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=270289 Instructions Using the following options: ...

You will need three pairs of heat-set inserts for the bottom two mounting holes and the belt clamps. The bolts that go through or into the mount should be selected for fit, they should be shorter now than in the Voron documentation. This includes...

You may have noticed an extra part to connect the stem to the top plate, but in the final design I eliminated this and just designed the long stem coming out of the top plate. I did not need to print it again since I already have the prototype, so...

Here are some of the parts that I used: WINSINN MK8 Drive Gear Extruder Hotend Feeder 40 Teeth 5mm Bore Stainless Steel for CR-10 CR10 Prusa I3 https://www.amazon.com/gp/product/B077GP454R/ref=ox_sc_act_title_1?smid=A2QQQKMKGVNA5E&psc=1 HUABAN 10pcs...

the TMC and T15 adapter looks very similar in design https://www.bitchute.com/video/NZlRmetBmjad/ link to the Installation video of the T15 and TMC magfed adapter update 23 06 2020_____ new mag release button wide added. Update: 8-10-2020 mag...

The inspiration behind this project comes from Autonomous Plant - Proof of Concept found on YouTube at https://www.youtube.com/watch?v=XFOcX6E8lGI. So far, the following parts have been created: A bottle funnel was remixed from a design available...

The exhaust half and the fan carrier half are then mounted bedside-to-bedside with 8mm M3 screws. The fan is installed last since it obstructs these screws. I started with the 40mm fan version, but soon discovered that regular fans are not good at...

So when I started planning the installation of OctoPrint, I was looking around for a camera mount. The key was mounting the camera on the printer bed so resulting timelapses are much better. I found the beautiful mount design from Jerware at...

Here's a step-by-step account of how I brought this project to life: 1. The LED panel arrived, and it was time for its first test. 2. After making necessary adjustments, the first prototype took shape. 3. With each refinement, the clock neared...

It supports the following: - AM312 motion sensor - BH1750 light sensor - SHT31-D temperature and humidity sensor Features - USB charger can be rotated to accommodate different outlet orientations - Small PIR motion sensor housing can be angled...

Updated 19/01/2018 - Rework the sides of the LCD punchout and the IEC punchout to improve the fit. Printed my final piece at 0.1, 100% infill. Added pictures showing wiring diagram, blue is neutral, stripey yellow is ground and the brown (or is it...

The nozzle will experience a small amount of heat droop on its first print, so some sanding may be needed to re-flush but seems to settle after a couple prints. Benchy test in ABS: A Benchy photo is shown in ABS at 0.1mm using version 3 without...

Customized version of created using the Customizer!. ... Instructions: Use these options for your print: - build_plate_selector = 0 - tolerance = .5 - box_shape = 1 - box_height = 30 - box_maximum_length_or_width = 120 - box_top_height = 10 -...

This case does have a piece of acrylic to protect the watch display along with a micro usb to type C adapter to utilize a type C charging cable. I wanted to make a case where you didn't have to get too much to put it together. The acrylic along with...

If you're not getting a good seal use some electricians tape or a piece of latex glove to improve the seal. Print Settings Printer Brand: Prusa Printer: i3 MK3Rafts: No Supports: NoResolution: 0.2 Infill: 15% Filament: [ CCTREE PLA...

After receiving my Ayaneo I wanted to get a stand/dock while waiting for the official dock to arrive.  I looked around for some alternative but did not like any of the commercial stands that people suggested. I did print the other stand that was put...

WIP! Heavy duty camera slider Designed for use with 25mm chromed steel pipes (https://www.bauhaus.se/dp-ror-millers-25mm-krom.html) or Aluminium (https://www.bauhaus.se/ror-aluminium-o25mm-1m.html) When printing, choose between Roller v6 (608 ball...

It has internal dimensions of 80.5 x 117 x 28 mm, so it should work with most 2.5" drives Seagate has made in recent years. I have not tested it with WD drives, as I do not have any.</p><p>I created a lower plinth to hold up the bottom drive to allow...

... good. Please be aware of this&nbsp;Print settings:No supports0.2-0.3 mm layer height will be good enough for looks and strenghtYou can add brim if the adhesion is not so good, should be easy to removePrint orientation should be as on the pictures

The height of the end is 0.267", as verified by Michael in the Full Spectrum Muse Hobby Laser group on Facebook, and my printed billet matches it closely. If your printed billet is slightly high, simply sand it down or adjust it in the slicer until...

###If you like my work, you can support me through Patreon: https://www.patreon.com/gigapenguin3dprints/posts Description ==================== The display will fit all Tarmac Works release of the same casting. It is not tested with the other Pagani...