models forum

Test Print Video here: https://www.youtube.com/watch?v=H8vL2GeMYMQ Previous version here: https://www.thingiverse.com/thing:4650517 As per the previous version a big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken...

You may also be able to gently fit the parts into each other and twist to get a sense for how smoothly the connectors fit. Place in a sealable/zip-top plastic bag. Print and fill out a form to help the hospital and make certain that you, as a maker...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Scaling up the model to increase the included printing gap, will stop it fusing if this occurs.Step 5Now to starting turning the collar back and forth to try and loosen it up. The box closes by twisting the upper collar anti-clockwise (this can be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 74 printer_tolerance = 0.4...

Externally modeled accurately from my real life Amiga 500+. Video of Doom Eternal on it: https://youtu.be/lsHi1vf_0Z4 Advanced project for builders that know how to fabricate some things like cables and adapt and paint parts to fit their hardware....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...

The problem is that the individual mirror cells overlap and when I separated the cells into parts of the larger array, each cell along the perimenter got the full width base perimeter border and so they bump up against each other instead of...

So, don't be alarmed if you notice discrepancies.) And another NOTE: If you're looking to upgrade the model cooling blower to a 5015, I have something very similar to the Z-19, but which supports the bigger blower: I called it the "Z-23", and here's...

Components used: An SG90 9g servo motor: https://www.amazon.fr/AZDelivery-Digitales-Micro-Servo-Parent/dp/B081Z5V3M2 https://boutique.semageek.com/fr/104-micro-servo-tower-pro-sg90.html?search_query=sg90&results=1 a paper clip glue to assemble the...

I modeled the general design of these connectors after Spears brand Dri-Splice connectors (http://parts.spearsmfg.com/sourcebook/TURFTECH_TURF_IRRIGA_T_TURF_DIR_T.pdf). Most of the good professional landscape light and outdoor audio companies in my...

The STEP file is included for easy remixing. Please post any makes and if you see a problem please post a comment. Updates: 4-30-2020: Thanks to feedback, I corrected the model for the base, the updated version is "6I". ...None of the other parts...

1 slot for a pair of Kitchen shears and 1 slot for a Honing/Sharpening Steel.I designed the model into 4 printable parts so this could be printed on smaller printers like the Prusa Mini. But this also makes for easier cleaning since the bottom and...

You may need to adjust your switch's orientations in the holes depending on your model of keyboard switch, so be prepared to work through that. 13) Lay in the keyboard-switch-populated 3D-printed piece so that the pins face towards the inside of...

----------------------------------------------- MATERIALS ------------------------------------------------------ - Raspberry Pi Model 3 B (This is what I used but really any micro-controller can work) - Breadboard - Mini-Breadboard - 10K Resistors...

This is then seen when viewing the seam around the edge of the keyfob - everything should line up, with the flag the correct way up when viewed with the keyring hole on the left-hand side.Building the layer cake...Drawing the Union Jack - In the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

This has taken several months to work out the kinks, but I think I have a good working model now. However, here are a few things to note: Prior to any assembling of any of the parts, I have found it is best to pre-thread all of the screw holes...

Make sure to follow me to get a notification when it's uploaded!*** ------------------------------------------------------------------------------------------------------------- ###READ BEFORE PRINTING!### * First of all, this is a non-commercial...

Microstepping is not saved in the EEPROM, that's why this needs to be in your startup gcode. CREDITS : Prusa R4 extruder : https://github.com/prusa3d/Original-Prusa-i3/tree/MK3S CAD model for Bondtech gears :...

If you have a tuned in printer, bump the speeds up a little for a dramatic improvement, (make sure wall thickness is a multiplier of your nozzle thickness - The parameters are important and there are a lot of dependencies, Make sure you have done the...

This has taken several months to work out the kinks, but I think I have a good working model now. However, here are a few things to note: Prior to any assembling of any of the parts, I have found it is best to pre-thread all of the screw holes...

Two B2s stacked works well for going higher.Related Links: Magnet Insertion Tools for Bases Drilling Guide and Magnet Insertion Tools for Walls Door Frame Adapter for rbross DoorsCompatibilityThe short tiles (Row A and Column 1) are also compatible...

If you use OpenSCAD, the model could be adjusted further refine the diameter of the internal air channel for your needs. Caution, because small changes in diameter produce big changes in airflow! Print Settings ========== The dimensions of...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

I have also designed a suitable molle mount for this grenade, that will also fit perfectly to my 40, 60 and 80mm wide adjustable belt clip system B.C.S: https://cults3d.com/en/3d-model/various/rcs-indiparts-ml3dp-b-c-s-belt-clip-system You can print...

Your purge block will be rather large, so if you have a suitable item you can use as a wipe model, use it! Then, remove the 8 outer-most parts and core, leaving just the inner 9 components. You will need to reassign colours, i.e. red becomes the...

 - INCOMPLETEAdd variation with looser tolerances so pots can rotate freely - INCOMPLETEAdd small washer to fix noise issues some have experiences - INCOMPLETE As with any of my models, feel free to message me with any questions or...