models 4d

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

It can support itself and needs a lot more force to be bended. If you still want to print your own loc line, I used the models from MinyMan644 found here -> Loc-Line Fittings (1/4", 1/2" and 3/4"). I strongly recommend buying loc line instead of...

... find sellers on Amazon.com or Aliexpress.com. This is still a working project. I will update the bill of materials I used, add more models for RPi 3, and sensors when they are done. ...If you have any comments or suggestions, please let me know.

This was a fun project but before starting, I recommend you read the 3D model description and 3D print settings. Also refer to all the attached photos. In addition to having a 3D printer and filament, below is a list of tools/products that I used to...

My Fritzbox 7590 is an early model (article no. 2000 2814 with the thin housing with two rows of grill openings at the gray back). Later versions of the 7590 have a beefier housing and more grill rows at the gray back. They will require you to...

Adding LED lighting to the model is optional and not a requirement for the functionality of the stand, and it's up to the discretion and electronics capability of the user. There are holes at the back of the stand where you can slide in some LED...

It was hard to get some screws in it so I had to manually remove parts that model has removed for you. Make sure if you use screws to hold bearings tight, lowest ones have low-profile heads or they will be lower than extruder nozzles and hit your...

... diameter of the hose end 30mm away from the tip (the wider part) This will give me the diameter and taper needed to revolve a new part for anyone who wants one. Please let me know what make/model it goes to and I'll add it if I am able. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

... The models are in the position, they should be printed. No support is needed. I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this tall piece. Printed on an Ender 3 Have fun!

All of the parts are assembled with pressure fit slide connections, and I added some vaseline between the parts to make it more airtight and to allow them to more easily come apart for service. I ended up cutting off the top tab on the Here are the...

The firmware numbers will match regardless of your printer model. If you use a slicer that requires EEPROM, make sure to update your EEPROM settings to match your new firmware. The easiest part is printing the adapter plate - any ABS or PLA preset...

I printed the nuts and locks in a bright colour to highlight their function and make them easy to find if they were to fall off. I have uploaded a 3mf file containing all the parts in the correct orientation on the build plate, however you...

 If you intend to use Sovol's SV06 Plus hotend, you'll have to get or make a duct that will work with the tall heatblock.I included a few models from Sovol's github, to include their extruder knob and extruder release lever, for no purpose other than...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Have a look at this Prusa blog post. Note that the parts will only come into contact with clean water so I just used mine as printed. You might want to sterilize the printed parts and the float valve when cleaning your sprouter (eg, using a...

Long story short, these gears don't work in the real word unless you really really know what you're doing (like how to avoid the bending because you know your material strength properties and your torque forces and more I don't know) Support me...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

Quick release (keyed-slot) analog module bay for Walksnail Goggles X and DJI V2.Have a look at the awesome original model first. This remix replaces the main body and the “B” mount adapter plate that gets screwed to the back of the main body. The “A”...

This fits in a 35mm (1 3/8") hole that you should drill in the rear-center of the unit Instructions My pipe had an OD of 60.5mm and I rounded up to 61 in the model. It's a great fit and I've included the SCAD file if you need to modify this diameter....

And yes, I'm already working on another version to fit the standard width tank; it shouldn't be too difficult to scale it down from the XL model. I've also come up with an alternative design - a curved blade that's just as effective but looks much...

It works alright as it is but it does bounce around sometimes (most notable as read below; CONS). TL;DR PROS- Works with common SN04 leveling sensor Sensor range covers the entire area of the hot bed. Fine tunable height adjustment by turning an M3...

There's the distance between the pin latches and the depth of the back cover recess defined by the svg, and then extrude the profile using whatever modeling software will accept an svg to the width of the pins. I personally used Inkscape and FreeCAD,...

The RR35 is the smaller model but has the type of pod I wanted. It stands 35 meters high, so I decided to scale mine at 1/35. My project was created on SOLIDWORKS for design and printed on my CR10 stock machine. The wheel is quite large, standing 1...

Required Components Arduino Mega 2560 (You must use this model because you require at least 25 I/O pins) ProtoShield for Arduino Mega 2560 (Highly recommended) (Example ) 12 LEDs (I used 6 different colors) 12 Resistors with the correct resistance...

This is a 1:50 scale model (metric) of a space rocket that transforms into a Mars base. (well, conceptually) Instead of building vehicles to transport pieces to build a base, it seemed more reasonable to use the whole spaceship as the future...

Enjoy my Ulvheim Small Merchant House. It came from my Patreon February Release. Thanks to all my supporters and to Markus Kruse / Terrain4Print, creator of the Ulvheim City. This model is supportless as usual. :)</p> <p>Discover my Ulvheim Remixes...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 stencil_pattern_line_thickness = 30 printer_tolerance =...