modeling rangers

Really like the wheel from TheSloppyApprentice's Watermill and was looking for ways to hold it besides that large frame in the source.So I could make it stand in a bassin or hang under some opening where water is dropping off.So here are 2...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Subsequently, Bondtech integrated this improvement into their model.This is what you need:Gears, bearings, and screws set (you can take yours from your BMG extruder)                 ...

You can generate models for each part separately by editing SCAD file. Just comment out hanger(); or ex_bracket(); at the end of the file! ... You can find complete how to upgrade article on my site: http://lensdigital.com/home/?p=1498 Credits for...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_pattern_thickness = .8 custom_back_extra_port_y_size = 30 custom_back_camera_corner_resolution = 8 custom_top_port_x_position = -10...

I won't go into any more detail because it involves mains wiring and if you're legitimately comfortable with mains you should be able to easily wire it up any way you please. The cover has melted/pressed in brass M3 Threadletts for durability. The...

Print the bumper pin two more times (for a total of 3 bumper pins) and print the pusher pin one more time (for a total of 2 pusher pins) Before printing out the ball, slice the model in half horizontally and rotate the bottom half 180 degrees...

The resulting "cylinder" is much stronger - I even tried to bend/break it without success. The hole piece was created with the following drafts and results : Bottom row, through holes (left to right) : 1/2° draft = very tight fit, very difficult to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

NOTE: all models are at initial stage and not refined, nor optimized for printing, only a rough idea at the moment The unmanned colony builder/Mars MkI is a project that seeks to automate the construction of shelters and basic facilities that a...

...All "mandatory" supports are already in the model. This piece on the photos was accidentally done with 0.15mm layer height and it turned out fine, although I intended to print it with 0.08mm height. Everything from 0.1mm and below should be alright.

Tensegrity model maintaining stability with one single wire.Materials needed:0.5 mm nylon wire7x M3 nuts7x M3x10 mm Allen screws (longer ones were cut to the right size)wooden plank of about 55 cm2x 50 mm wood nailsThe spiral parts are designed to be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 11 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

You have arrived at the "first three faces" - model one above. Next form a plane from the intersection points and the axis of rotation. Cut away from that plane. Voilà. Octahedron. NEW: Ten-sided added, and rounded and squished. Also blank. Simply...

I needed a quicker and simpler solution to perform these tasks so I could focus on slicing and printing actual models. What is more basic than some good old push-buttons? Feel free to remix it as you wish. It would be nice if you upload the remix...

Keep doing it until you get a reliable contact. Multi-color printing For printing in multiple colors, you need to slice the model and save it as normal gcode. Then, you have to insert the M600 command. You can do this manually by opening the gcode,...

They are press fit and held by friction only and on my prints are very secure, they snap in pretty securely but can relatively easily be removed by getting a nail in the seam then wiggling. How I Designed This I created this because I wanted to have...

It was just hard to get some of the screws in it so I had to manually remove the parts this model has removed for you. Make sure is you use screws to hold the bearings tight that the lowest ones have low profile heads or they will be lower than the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

As such, some knowledge of manipulating 3D models will be required in order to make use of these. Since I created them, decided may as well share in case someone else can use them. You can see the principal that allows these masks to work in...

Updated parts files, and partial instructions will be published here as I go along, to be replaced (eventually) by the full instructions, final stl's and Blender source file (yes, I modeled this in Blender), but there is still a lot of work to do,...

When I figure out a way to secure both together and close the gap, I'll update this model. If you wish to have a display base tweaked to fit to a different car from a different brand, please send me these dimension for the display base holes:...

I had no trouble pulling the mold off the lettering.For creating the CAD model, here are the basic steps I used :Create a “slab” large enough to contain the desired lettering, with additional space fora removal tabCreate raised lettering on the slab...

This is a model of a convenient sliding lid box with an easy to use locking mechanism consisting of a bump on the lid that keeps it securely closed. Note that for slim boxes the lid does not bend as much and the locking and unlocking may be a bit...

Just make sure to get the alignment correct before letting the glue set up!Notes:Raft:              YesSupports:    NoI've had the best luck printing these using a single-layer raft, with the part oriented...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

I also added some rubber feet to give a bit more stability.If you need to modify the enclosure for different model IEC connectors or E-stop buttons the STEP files are provided as well as a link to the original Onshape document.Onshape Document:...

Commercial CTDs are expensive, with the most affordable models costing as much as $6,000.00. This can be a prohibitive cost for near-shore oceanographic research on the continental shelf, where the water depth rarely exceeds 200 meters. The expense...

The freecad file is made with: Realthunder Branch Word size of FreeCAD: 64-bit Version: 2023.131.26244 +5365 (Git) AppImage Build type: Release Branch: LinkDaily Hash: 73c4ca254c5de8849d104973482e98399fb24863 Python version: 3.10.8 Qt version:...