model turbofan engine

You can use Fusion360 to work on it if you don't have Inventor. ENJOY!!!! THE MODELThere are two options for the lid:with TPU sealwithout TPU sealI would suggest to try the sealed version if you have a little bit of TPU laying around. You...

I have completed the task, which is an intricate and comprehensive model. It required two full weeks of my time. I eagerly anticipate your appreciation for it; have a great day! :) :)</s> щ поставих задачата, която е детайлна и обширна конструкция. Я...

You may need to adjust your switch's orientations in the holes depending on your model of keyboard switch, so be prepared to work through that. 13) Lay in the keyboard-switch-populated 3D-printed piece so that the pins face towards the inside of...

Test Print Video here: https://www.youtube.com/watch?v=H8vL2GeMYMQ Previous version here: https://www.thingiverse.com/thing:4650517 As per the previous version a big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken...

Z gap between support interface and model is 0.2 mm For the adapter plate I used standard supports with the same support options Other parts: For convenience, I included the 40 mm fan cap, part cooling duct and BLTouch mount from the original...

1 slot for a pair of Kitchen shears and 1 slot for a Honing/Sharpening Steel.I designed the model into 4 printable parts so this could be printed on smaller printers like the Prusa Mini. But this also makes for easier cleaning since the bottom and...

To prevent that, don't hesitate to rotate horizontally one the stack 90° clockwise or counter clockwise, to prevent symetric parts interlocking each other.More than two player can play together if another set of tiles is printed.The printsThe 3D...

If the diameter of the mounting holes (see diameters in the image above) of your driver is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit. <b>PRINTING / ASSEMBLY. </b>This...

Supports are built into the models. The fan shroud should be printed with the blower mouth facing up. Trim off the bands tying the barbell studs together and remove the two pieces that support the shelf at the rear.</p> <p>Some good print settings...

This is a Core XY conversion kit for the Ender 5 with Linear rails There is a MK2 version here:https://www.thingiverse.com/thing:4777606 Big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken the belt tensioner detail...

To do this, I will add the foot models in STEP format, they are easy to edit. Assembly video: https://www.youtube.com/watch?v=zzjLTr3RoPg https://www.youtube.com/watch?v=Tg764du-zTU https://www.youtube.com/watch?v=Vcvz-GSpdps With a 3S...

To aide in designing this part, I also ordered a complete Neo hotend assembly from Amazon so I could 3d model all of the parts. Unfortunately, the back plate is not available to buy, but I was able to download an stl file from another Thingverse...

You can hold them in place with either ¼" wooden dowels or printed plastic cylinders.Next, glue the battery and motor carriages to the drivetrain as indicated in the CAD model. Drop a M3 screw (or plastic pin) into the slots, and insert the battery...

&nbsp;&nbsp;ENGLISH-------------Only tested on T12-X, but can work on equivalent models with boxes of the same dimensionsI found my T12-X soldering station a little too bulky, the screen not very visible and too dark. I also wanted to have all the...

We also offer other variations of this light if needed to fit your specific application, 120-277V AC, 12-24V DC, and 0-10V dimmable models.Our EPL-24-2L-LED-480V LED light fixture is NRTL Listed for United States and Canada approved for use in paint...

We also offer other variations of this light if needed to fit your specific application, 120-277V AC, 12-24V DC, and 0-10V dimmable models.Our EPL-24-2L-LED-347V LED light fixture is NRTL Listed for United States and Canada approved for use in paint...

The XIAO is also able to be soldered with castellated holes for a low profile.KeyswitchesI designed this to be compatible with Cherry MX 3 and 5 pin models. These are easily accessible in packs of 10 or more.Circuit BoardI designed the circuit board...

Once you have the rights % size change, you can Meshmixer or TinkerCad any model onto the clip_in_insert to create all kinds of new experiences for your animals, or useful things such as a cover for a feeding area to prevent gunk from falling into...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Verify the axle turns freely. Source File FreeCAD: BearingPegV4_2019.FCSTD Reinforced Within the pegs (excluding the original V4) 'pins' are embedded that promotes a strong cross pattern with lines at the stress point in addition to beveling....

... zip tie. (Optional) Install Anti-Skid pads on the bottom of your new drybox to help keep it stationary while printing :) If you found this model useful please consider leaving a comment, posting a make, or donating filament to fuel my experiments.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

All the slicers I tried will still slice the model correctly.&nbsp;Parts I used:roller switch:https://www.banggood.com/5Pcs-AC-125V-1A-Mini-SPDT-Micro-Switch-Long-Hinge-Roller-p-998613.htmlslide...

This brings the Muscle v2.0 advanced cooling system, originally designed primarily for Longer and Alphawise printers, to many more 3D printer models and users. I am even working on testing a custom X-axis mount plate for Prusa/Wanhao and other I3...

This model is intended to be glued together using Gloop! Get your Gloop! here: </strong><a href="https://3dgloop.com/shop"><strong>https://3dgloop.com/shop</strong></a></p><p>Assembly made without using Gloop! may result in the need to prepare for...

The Version 1 is based on the original model, but with added material to compesate the extended face on the striker, and the second one is something I made because one of my magazines was giving me trouble, not really stoping when it needed. See what...

Winston sculpted reproduction of Schwarzenegger's face in several poses out of silicone, clay and plaster.[41] The sequences set in 2029 and the stop-motion scenes were developed by Fantasy II, a special effects company headed by Gene Warren...

This seems to be a weak point in all reciprocating saws and is a particular problem with this model, with some users reporting that the blade clamp had sheared off after only relatively light work. Replacement parts are available, but at a...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers).For adjustable friction, I've added a simple bail that attaches to...