model connect

Supports are built into the models. The fan shroud should be printed with the blower mouth facing up. Trim off the bands tying the barbell studs together and remove the two pieces that support the shelf at the rear.</p> <p>Some good print settings...

To use a different font than the standard Roboto (English) for either (or both) of the lines of text you just need to install the font onto your machine and configure it in the model parameters (in Customizer *locally* or in your .json file, more on...

I added some build notes below and a BOM which doesn't include screws, wires, connectors, etc., but has all major components.&nbsp;I planned to revisit this model and release a better version. However I have at least a year's worth of projects in...

And Happy Printing!-------------------------------------------------Originally designed in Fusion 360 and printed with Prusa Mini+&nbsp;THIS MODEL IS UNDER CC (Creative Commons) LICENCE.&nbsp;Note: The DO NOT EAT sign might not print properly due to...

Moreover….Sitag astonished me a lot because actually….they continue to make and sell the same model: the famous “Sitag Reality”…which costs now around 700€ !!!Therefore, I decided to try a repair with my engineering skills and a big dose of...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

You can use Fusion360 to work on it if you don't have Inventor.&nbsp;ENJOY!!!!&nbsp;THE MODELThere are two options for the lid:with TPU sealwithout TPU sealI would suggest to try the sealed version if you have a little bit of TPU laying around. You...

While his drinking-glass method worked for me, I could not get the parts of his model to fit together well, because my printer does not appear to be tuned well enough. Note that the guide is all Denny's work, refined by him in many months. My...

I just have to choose a bulb of the wattage I want and with a high CRI to get the best image quality.Since Fresnel spotlights are a classic in the world of cinema, I based my project on a model of the Arri brand from the 1940s. Which has a spindle as...

This model is intended to be glued together using Gloop! Get your Gloop! here: </strong><a href="https://3dgloop.com/shop"><strong>https://3dgloop.com/shop</strong></a></p><p>Assembly made without using Gloop! may result in the need to prepare for...

These parts were designed using advanced 3D modeling techniques, and are not intended to be changed by introductory students. We designed the VeggieMake pins using Tinkercad. We chose to use Tinkercad because we feel it is the best platform for ...

Components used: An SG90 9g servo motor: https://www.amazon.fr/AZDelivery-Digitales-Micro-Servo-Parent/dp/B081Z5V3M2 https://boutique.semageek.com/fr/104-micro-servo-tower-pro-sg90.html?search_query=sg90&results=1 a paper clip glue to assemble the...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

&nbsp;- Click on the "Download" button and you will find the download file in small print coloured light grey below the Model &nbsp;files.&nbsp;Using Onshape is easy - open the attached link, and double-click on the #BOTTLE_DIAMETER parameter to...

It features several small niceties, such as a water inlet that optimizes top-water removal, using magnets instead of suction cups, a 'vacation' mod for skimmer waste overflow, snap-on piping for secure fitting, and much more.Please note that this is...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

Filament Dry Box (Peli Case) Storetwo standard 200mm filament spools in an air-tight Peli Case. Perfecting for storing your hygroscopic filaments after drying. The Dry box can be configured to simply store the filament, or by drilling and tapping 4 x...

... zip tie. (Optional) Install Anti-Skid pads on the bottom of your new drybox to help keep it stationary while printing :) If you found this model useful please consider leaving a comment, posting a make, or donating filament to fuel my experiments.

The Hearst Tower, designed by Norman Foster, perfectly embodied the figure of the king with its massiveness and magnificent exterior.After determining the arrangement of the buildings, the next step was the creation of working models, which were...

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...

The Version 1 is based on the original model, but with added material to compesate the extended face on the striker, and the second one is something I made because one of my magazines was giving me trouble, not really stoping when it needed. See what...

I have no immediate plans of adding a mount for a counterweight because everyone will find differently shaped ones _____________________ **Edit: ** Added an adjustable version of the speaker caps and a locking buckle ___________________ I wasn't...

Please check the images to see what it is included in this kit.This set contains: - Draconian Shock Troops (12)- Assault Dragons (4 + 4)- Commander Drakvarr- Flamagath Blackflame- Azgrathok - Chaos Dragonlord- Onixia the Tempest (Draconian Pinup)-...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

As provided the enclosure is set up to accept a 9.7" 2048x1536 panel as used by some iPads - Model No: LP097QX1-SPC1 https://it.aliexpress.com/item/1005002113658592.html There is no reason why you couldn't use any alternate panel and suitable driver...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

The solution is simple enough: Both parts of the model need to be placed away from the centre point (still properly lined up with one another, obviously), so that the probe can do its thing without the first print getting in the way. So began attempt...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...