model animation

The attached model is sized to fit the Eye Cu Smile V2 and V1 filter housings at 45 mm OD and 10.5mm high However if you want to make any size antimicrobial / antiviral filter meshes for any purpose then even sketchup will suffice Steps to draw a...

If you don't want to mess with a PLA support, you could probably print this part in two separate objects.I provide you the Fusion 360 file, so you can customize and change the model according to your rail system. I strongly recommend you to...

 900mm in length (shown in the picture is a bit too long, you may want to use 800mm instead)The bamboo skewers seems to come in different sizes, so use the file that closest match the skewers you have and scale the model accordingly.  If...

UPDATE 09.08.2022 •changed length for diffusor and mount from 10mm to 100mm •orientation changed for some models •added end cap UPDATE 12.08.2022 •added with diffusor / without diffusor comparison photo and electronics box wiring photo •added...

Please check the images to see what it is included in this kit.This set contains: - Draconian Shock Troops (12)- Assault Dragons (4 + 4)- Commander Drakvarr- Flamagath Blackflame- Azgrathok - Chaos Dragonlord- Onixia the Tempest (Draconian Pinup)-...

But don't hesitate to choose the one you prefer.The Raspberry Pi racks I designed are compatible with the Raspberry Pi 2B, 3B, 3B+ and now with the 4B models.I also added a rack version that doesn't use the snap&lock system ("Rack_RPi3&4_S"),...

You can use Fusion360 to work on it if you don't have Inventor. ENJOY!!!! THE MODELThere are two options for the lid:with TPU sealwithout TPU sealI would suggest to try the sealed version if you have a little bit of TPU laying around. You...

Theoretically, it can run more than 11 hours on 1 load (not tested). What parts do you need?Plastic parts:You can use the print files if you have an MK3S or you can use the model files and set everything up yourself. The photos show the position...

The Version 1 is based on the original model, but with added material to compesate the extended face on the striker, and the second one is something I made because one of my magazines was giving me trouble, not really stoping when it needed. See what...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

... pictures are from Printable Heroes. They do not sponsor nor endorse these stands, but they do indeed offer a great variety of models —many of them for free. ...They do also have several, very affordable Patreon tiers —I suggest to check them out!

If you have a tuned in printer, bump the speeds up a little for a dramatic improvement, (make sure wall thickness is a multiplier of your nozzle thickness - The parameters are important and there are a lot of dependencies, Make sure you have done the...

Bear Exxa 1.0 is available here: https://www.thingiverse.com/thing:4362586 IMPORTANT: The Bear X axis will currently limit you to what alternative extruder/tool options you can mount without creating an adapter plate as it is different than previous...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

Make sure to follow me to get a notification when it's uploaded!*** ###READ BEFORE PRINTING!### * First of all, this is a non-commercial print, this means you are not allowed to sell files or prints of this model. Not that I neccearily would have...

If you are using ceiling pipes, I've modelled the right side of the pipes only. For the left side it will need to be mirrored in the slicer. The vents part is optional but I recommend glueing it to the roof. The vents piece can act as additional...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

... self sustaining for long periods. All ground piping, cabling and the Large Gas collection cansiters would be covered in Dirt once operational for Sun / wind shielding. Note the Space Suit man was inserted for size, got it from the NASA models site

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

On the bottom of the print there is a text saying “Valentine 2022”. In case a name you need is missing, you can customize the model to show it: Please install OpenSCAD on your own computer and follow these instructions.If you could take a...

 - Click on the "Download" button and you will find the download file in small print coloured light grey below the Model  files. Using Onshape is easy - open the attached link, and double-click on the #BOTTLE_DIAMETER parameter to...

If the diameter of the mounting holes (see diameters in the image above) of your driver is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit. <b>PRINTING / ASSEMBLY. </b>This...

... zip tie. (Optional) Install Anti-Skid pads on the bottom of your new drybox to help keep it stationary while printing :) If you found this model useful please consider leaving a comment, posting a make, or donating filament to fuel my experiments.

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture. .Wiring: These LED light fixtures...

(In the future, I'll model a printable screw-gun interface for people who can't get the part in question.) 4.#6-32 brass nut, 1/4" across (measured face to face), 3/32" thick (optional) McMaster-Carr 95130A120. Fits into a pocket on the gun carriage,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

I 3D modelled and printed some end caps for it with Ninjaflex so it doesn't scuff up my walls. 4/10 update: I added some parts that hold a 3/8" steel rod in the middle of the pull up bar so it isn't just relying on the screw coupler to hold the...