modded xbox 360 controller 3d models

The wire colours are different but the cable order is the same, I will get to this in the assembly instructions later.Earlier motors were rated at 0.5A peak and 0.35A RMS and are not suitable for this printer without lowering the voltage.Why?I have...

The wire colours are different but the cable order is the same, I will get to this in the assembly instructions later.Earlier motors were rated at 0.5A peak and 0.35A RMS and are not suitable for this printer without lowering the voltage.Why?I have...

The wire colours are different but the cable order is the same, I will get to this in the assembly instructions later.Earlier motors were rated at 0.5A peak and 0.35A RMS and are not suitable for this printer without lowering the voltage.Why?I have...

It's very important to use a high quality thermocouple that is rated for 500 C for example, the stock Qidi thermocouple is only rated at 300 C.If you want to increase the print temp beyond 300 C (stock) you can enable it in firmware, I have commented...

The wire colours are different but the cable order is the same, I will get to this in the assembly instructions later.Earlier motors were rated at 0.5A peak and 0.35A RMS and are not suitable for this printer without lowering the voltage.Why?I have...

It's very important to use a high quality thermocouple that is rated for 500 C for example, the stock Qidi thermocouple is only rated at 300 C.If you want to increase the print temp beyond 300 C (stock) you can enable it in firmware, I have commented...

They would need to know ESP's, addressable LED's, the FastLED library, light and temperature sensors, OTA (over the air updates for wireless uploads), WiFi (for time syncing, light and animation control)Code Update:There are two code files now. One...

PrinterMods MDD - THE CREALITY ENDER-3, ENDER-5 & CR-10 DIRECT DRIVE KIT - NEW V1.3 (https://printermods.com/products/direct-drive-mod-for-creality-ender-3-cr-10). If you still have not bought the DDX from bondtech this is what I would do if I...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

The tray should now slide into place.Installing Drawers/Trays under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will need to slide a “Rail Lock Upper” into place on the back of...

The rails are 4mm thick, so a faceplate should be 165.2mm wide (at a minimum) to cover the drawer and rails. See the Fusion 360 archive file for more details. There is a 2mm lip at the bottom of the smaller included plates. You can use this as a...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 15 shape =...

He also conquered Egypt, who had used coins since around 500 BCE but began to mint gold staters around 360 BCE. The Persians also set the standard that it was official governments who struck coins. Thus coins were one of many expressions of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes wall_thickness = 1.6 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

However, if they are made too small, they will not line up with the front plate grid.     -Adjust the length of the spring for more or less power (the fusion 360 files are available at the original source listed in the attribution...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 30 mirror = No shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

...  You can find the ones I have done any any people tell me about by going to the COLLECTION links in the links at the top.The Pivot and the spreader Install and AdjustmentThe pivot top gives you 360 degrees of rotation with 18-20 degrees tilt.

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...

 I'll be looking into ways to improve this. 3D ModelFor those of you wanting to modify and grow this design - I've included the Fusion 360 and STEP exports in the files section here.FEEDBACK WANTED! Because I live in a fire sensitive...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 15 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 mirror = Yes shape =...

Based on the names and values in this file, it seems like it might be configuration data from OpenSCAD or Fusion 360. OpenSCAD's "mobile_phone_customizer.ini" file format could be used here as it shares many similar parameters. I can give you some...

I used medium CA and CA activator to get an instant bond.Use a multimeter across the rails of one of the LED strips to verify that the strip isn't receiving more than its rated voltage (probably 12V) when the dimmer control is set to 100%.Battery...

3D Printed CNC (Computer Numerical Control) MachineDOWNLOAD Version 1.0 (2022-07-10) ZIP ~50MBHELP with images on how to assemble CNC Machine (external link)...INTROBelow you will find parts and tools, which will help you to print and assemble CNC...

While my tanks produced from these molds served perfectly, I do not have any control over how these molds are used by others, therefore I can not accept any responsibility or liability if any accident or fire is caused by the use of my design. Mold...

I have a drag chain for the gantry wires that lined up and worked well from that point.Route your hotend wires back to your control module as you like. I've got connector plugs in mine near the gantry which is easy and also looks like hot...

Adding a squeeze or lever type high pressure nozzle makes it convenient to turn water on/off as you need it since you're no longer messing with temperature controls too. Wet yourself, then lather up without water running, then spray off the soap when...

ENGLISH-----------------V2 Version with speed control: https://www.thingiverse.com/thing:5438282I wanted to make a smoke absorber that was powerful enough and could quickly cool an electronic board after soldering or desoldering with hot air by...