moblite 7 3d models

Insta360 Go2 mount for Happymodel Moblite 7

I found the settings on the site https://oscarliang.com/flash-betaflight-moblite-6-7/, there, in the comments, MATTI offers settings for Mobline6, gives a link to google drive. I partially applied these settings for Moblint7 with them it turned out...

... other tinywhoops. ... the battery tray fits the stock 650mah happymodel batteries, but if u ask nicely than i can make a version for a specific battery size. If you dont know, the moblite 7 has a runcam nano 3, so this was designed for that camera.

A light, top mounted battery canopy for moblite 7 and other tinywhoops. the battery tray fits the stock 650mah happymodel batteries, but if u ask nicely than i can make a version for a specific battery size. If you dont know, the moblite 7 has a...

This is a simple case to protect the Moblite7 when transporting it. I didn't make a lid for it since it fits fairly snug. I'm a novice at making 3D models so I wasn't able to get the case thickness to be uniform. It's about 2mm in some places and...

Intended for new pilots practicing indoor, for slow flying and hovering. Camera angle is 0. I made if for myself to learn to fly indoor in acro mode and to give protection to the control board and not to add much weight. It weights less then...

Case for USB charger HV battery Moblite 7

None of the canopys other pepole made printed well, or were not the perfect size. Also other canopys I looked at didnt have an adjustible cam angle so i added that to my design as well. Made a 2nd version that is heavier but stronger. Wheight: ...

None of the canopys other pepole made printed well, or were not the perfect size. Also other canopys I looked at didnt have an adjustible cam angle so i added that to my design as well. Made a 2nd version that is heavier but stronger. Wheight: -V1:...

I believe the moblite 6, 7, and mobula 65/75 all have the same bolt-up so this may work for all 4. IMPORTANT: This is press fit on the camera, so its tight. Take a knife and scratch all 4 internal corners of this mount until the camera presses...

Remixed a canopy model : - Added camera tilt - Added Flight Controller protection Only 1.7g Tips : Use tape to fix camera inside the mount, make holes bigger if your printer resolution is not good enough. ... Check out my video where I...

not really a remix but a redesigned hard canopy for the happymodel moblite inspired by angry don's version. print in PLA flat to the build plate using supports for the optimal structural strength. only 3 screws needed. ...weights about ~1.2g.</p> ...

not really a remix but a redesigned hard canopy for the happymodel moblite inspired by angry don's version. print in PLA flat to the build plate using supports for the optimal structural strength. only 3 screws needed. ...weights about ~1.2g.

this is a remix from angry don moblite canopy to add a fin too make the turtle mode easier lay the model flat on the post and use support to print. ... I was able to get my best results with a 0.2mm nozzle

There's a big set of screws on amazon for $7 that has the screws that fit the moblite. It comes with 1.2mm screws. I like the 1mm screws. You will need 1.2mm x 4mm, 5mm or 6mm will work also As always with these smaller prints, print 2 at a...

I recommend an assorted screw kit from amazon for $7, mines had 750 screws ranging 1mm-1.7mm diameter, 3mm-8mm long For best results i print with a 0.4mm nozzle at a 0.2mm layer height. The electronics cover is a remixed. Printer must be dialed...

This will not fit the Moblite in original configuration with the cam between the ducts. I don't agree with that design and the first thing I did was put the cam in a more traditional canopy (also my design). ... Update 3-23-2022 Added lid insert...

Only fit Happymodel diamond FC or moblite 6 and 7. Fit Runcam nano 3 all lens version (need a screw to secure on up corner). Mounting tutorial is here: https://www.youtube.com/watch?v=V1F7bQKi0n0 It a bit taller on the front to be able to mount...

a tiny whoop canopy with a fixed cam angle. ...The options are 15,20 and 25 deg.

This is Angry Don's Angry moblite 6 V3 canopy just a little bit slimmer and narrower to reduce the size and weight V2 is even thinner and slimmer

My version of canopy for HD whoop based on moblite 7 frame. 2 versions: higher / lower canopy Weight: 1.4g No supports worked fine on my printer. Print on the legs like its supposed to be on the whoop. You can pick version of the cam holder you...

Angry Don's Angry moblite 6 V3 canopy with extra hole to reduce cam tilt.

Moblite 7 camera mount remixed. ... Fit the hole in the pin that protrudes from the frame

This is a canopy for Moblite 7 (6). ... 20 degres cam angle canopy.

Custom canopy for mounting runcam nano 3 and insta360 GO2 in Happymodel X Angry Don Diamond F4 flight controller

added a spacer so i can use it for my Diamond Meteor Pro Pusher Mod: https://www.thingiverse.com/thing:5536503

40 degres tilt canopy for runcam nano 3 I use for my 14g world's lightest tinywhoop build.

I had issues with my moblite7 camera changing angles mid flight (crash) so I bought the mobula6 canopy and that introduced a bunch of Jello. My 3dprinted frame using M2 screws and I liked the design of this but needed larger holes. ... ...

7