moblite 6 3d models

I designed this for the moblite 6 with the help of RCgroups support. The weight ranges from 0.5g to 1.2g For a lighter print, print a 0.2mm layer height on a 0.4mm nozzle. The infill on the first 0.8mm determine the weight. For example: if...

Only fit Happymodel diamond FC or moblite 6 and 7. Fit Runcam nano 3 all lens version (need a screw to secure on up corner). Mounting tutorial is here: https://www.youtube.com/watch?v=V1F7bQKi0n0 It a bit taller on the front to be able to mount...

The L shaped peice goes on the bottom side of the mount after the main mount is screwed onto the moblite with camera in place. Take a 1-1.2mm x 4mm or 5mm screw and use the L shaped peice to secure the camera mount to eliminate vibrations. That...

This is Angry Don's Angry moblite 6 V3 canopy just a little bit slimmer and narrower to reduce the size and weight V2 is even thinner and slimmer

I believe the moblite 6, 7, and mobula 65/75 all have the same bolt-up so this may work for all 4. IMPORTANT: This is press fit on the camera, so its tight. Take a knife and scratch all 4 internal corners of this mount until the camera presses...

Remixed a canopy model : - Added camera tilt - Added Flight Controller protection Only 1.7g Tips : Use tape to fix camera inside the mount, make holes bigger if your printer resolution is not good enough. ... Check out my video where I...

Angry Don's Angry moblite 6 V3 canopy with extra hole to reduce cam tilt.

not really a remix but a redesigned hard canopy for the happymodel moblite inspired by angry don's version. print in PLA flat to the build plate using supports for the optimal structural strength. only 3 screws needed. ...weights about ~1.2g.

not really a remix but a redesigned hard canopy for the happymodel moblite inspired by angry don's version. print in PLA flat to the build plate using supports for the optimal structural strength. only 3 screws needed. ...weights about ~1.2g.</p> ...

This is a top mount replacement for the stock front mount camera. It is modeled to be printed flat with no supports. Mounts to existing screw holes with no modifications required. ...It prints much easier and faster than the other designs I found.

This is a remix of the compact pocket case of [PROwyant](https://www.thingiverse.com/thing:3590819) which can hold not one but two 65 mm quadcopters such as UR65/US65/UK65/Mobula6/Mobula6 HD/Meteor65/etc. ...or similar ones.

None of the canopys other pepole made printed well, or were not the perfect size. Also other canopys I looked at didnt have an adjustible cam angle so i added that to my design as well. Made a 2nd version that is heavier but stronger. Wheight: -V1:...

None of the canopys other pepole made printed well, or were not the perfect size. Also other canopys I looked at didnt have an adjustible cam angle so i added that to my design as well. Made a 2nd version that is heavier but stronger. Wheight: ...

I found the settings on the site https://oscarliang.com/flash-betaflight-moblite-6-7/, there, in the comments, MATTI offers settings for Mobline6, gives a link to google drive. I partially applied these settings for Moblint7 with them it turned out...

this is a remix from angry don moblite canopy to add a fin too make the turtle mode easier lay the model flat on the post and use support to print. ... I was able to get my best results with a 0.2mm nozzle

This is a canopy for Moblite 7 (6). ... 20 degres cam angle canopy.

Insta360 Go2 mount for Happymodel Moblite 7

This will not fit the Moblite in original configuration with the cam between the ducts. I don't agree with that design and the first thing I did was put the cam in a more traditional canopy (also my design). ... Update 3-23-2022 Added lid insert...

a tiny whoop canopy with a fixed cam angle. ...The options are 15,20 and 25 deg.

... other tinywhoops. ... the battery tray fits the stock 650mah happymodel batteries, but if u ask nicely than i can make a version for a specific battery size. If you dont know, the moblite 7 has a runcam nano 3, so this was designed for that camera.

A light, top mounted battery canopy for moblite 7 and other tinywhoops. the battery tray fits the stock 650mah happymodel batteries, but if u ask nicely than i can make a version for a specific battery size. If you dont know, the moblite 7 has a...

Custom canopy for Happymodel Moblite 6 and 7 from my original design. ... 0.6 to 1g depending on versions Available with differents tilt angle from 25 to 40 degres (angle in the file name) Edit 21/02/2021: -added 50 and 60 degres cam angle canopy -added...

Case for USB charger HV battery Moblite 7

Intended for new pilots practicing indoor, for slow flying and hovering. Camera angle is 0. I made if for myself to learn to fly indoor in acro mode and to give protection to the control board and not to add much weight. It weights less then...

This is a simple case to protect the Moblite7 when transporting it. I didn't make a lid for it since it fits fairly snug. I'm a novice at making 3D models so I wasn't able to get the case thickness to be uniform. It's about 2mm in some places and...

Custom canopy for mounting runcam nano 3 and insta360 GO2 in Happymodel X Angry Don Diamond F4 flight controller

added a spacer so i can use it for my Diamond Meteor Pro Pusher Mod: https://www.thingiverse.com/thing:5536503

I had issues with my moblite7 camera changing angles mid flight (crash) so I bought the mobula6 canopy and that introduced a bunch of Jello. My 3dprinted frame using M2 screws and I liked the design of this but needed larger holes. ... ...

40 degres tilt canopy for runcam nano 3 I use for my 14g world's lightest tinywhoop build.