moblite 3d models

this is a remix from angry don moblite canopy to add a fin too make the turtle mode easier lay the model flat on the post and use support to print. ... I was able to get my best results with a 0.2mm nozzle

Insta360 Go2 mount for Happymodel Moblite 7

This will not fit the Moblite in original configuration with the cam between the ducts. I don't agree with that design and the first thing I did was put the cam in a more traditional canopy (also my design). ... Update 3-23-2022 Added lid insert...

*********moblite race canopy v2" has the hole for the the spi receiver antenna. Wrap the antenna around the bottom of the flight controller and then into the bottom of the canopy antenna hole. Before you push it through the hole, put it inside a...

The L shaped peice goes on the bottom side of the mount after the main mount is screwed onto the moblite with camera in place. Take a 1-1.2mm x 4mm or 5mm screw and use the L shaped peice to secure the camera mount to eliminate vibrations. That...

a tiny whoop canopy with a fixed cam angle. ...The options are 15,20 and 25 deg.

Here's my lastest version of my angry moblite canopy with now adjustable tilt. Print in TPU or other fexible filament. Print flat with no support. Only fit Happymodel diamond FC or moblite 6 and 7. Fit Runcam nano 3 all lens version (need a screw...

I found the settings on the site https://oscarliang.com/flash-betaflight-moblite-6-7/, there, in the comments, MATTI offers settings for Mobline6, gives a link to google drive. I partially applied these settings for Moblint7 with them it turned out...

... other tinywhoops. ... the battery tray fits the stock 650mah happymodel batteries, but if u ask nicely than i can make a version for a specific battery size. If you dont know, the moblite 7 has a runcam nano 3, so this was designed for that camera.

This is Angry Don's Angry moblite 6 V3 canopy just a little bit slimmer and narrower to reduce the size and weight V2 is even thinner and slimmer

not really a remix but a redesigned hard canopy for the happymodel moblite inspired by angry don's version. print in PLA flat to the build plate using supports for the optimal structural strength. only 3 screws needed. ...weights about ~1.2g.

not really a remix but a redesigned hard canopy for the happymodel moblite inspired by angry don's version. print in PLA flat to the build plate using supports for the optimal structural strength. only 3 screws needed. ...weights about ~1.2g.</p> ...

A light, top mounted battery canopy for moblite 7 and other tinywhoops. the battery tray fits the stock 650mah happymodel batteries, but if u ask nicely than i can make a version for a specific battery size. If you dont know, the moblite 7 has a...

I believe the moblite 6, 7, and mobula 65/75 all have the same bolt-up so this may work for all 4. IMPORTANT: This is press fit on the camera, so its tight. Take a knife and scratch all 4 internal corners of this mount until the camera presses...

Intended for new pilots practicing indoor, for slow flying and hovering. Camera angle is 0. I made if for myself to learn to fly indoor in acro mode and to give protection to the control board and not to add much weight. It weights less then...

Remixed a canopy model : - Added camera tilt - Added Flight Controller protection Only 1.7g Tips : Use tape to fix camera inside the mount, make holes bigger if your printer resolution is not good enough. ... Check out my video where I...

This is a simple case to protect the Moblite7 when transporting it. I didn't make a lid for it since it fits fairly snug. I'm a novice at making 3D models so I wasn't able to get the case thickness to be uniform. It's about 2mm in some places and...

Case for USB charger HV battery Moblite 7

Angry Don's Angry moblite 6 V3 canopy with extra hole to reduce cam tilt.

added a spacer so i can use it for my Diamond Meteor Pro Pusher Mod: https://www.thingiverse.com/thing:5536503

None of the canopys other pepole made printed well, or were not the perfect size. Also other canopys I looked at didnt have an adjustible cam angle so i added that to my design as well. Made a 2nd version that is heavier but stronger. Wheight: -V1:...

None of the canopys other pepole made printed well, or were not the perfect size. Also other canopys I looked at didnt have an adjustible cam angle so i added that to my design as well. Made a 2nd version that is heavier but stronger. Wheight: ...

Custom canopy for mounting runcam nano 3 and insta360 GO2 in Happymodel X Angry Don Diamond F4 flight controller

40 degres tilt canopy for runcam nano 3 I use for my 14g world's lightest tinywhoop build.

I had issues with my moblite7 camera changing angles mid flight (crash) so I bought the mobula6 canopy and that introduced a bunch of Jello. My 3dprinted frame using M2 screws and I liked the design of this but needed larger holes. ... ...

Strongly inspired by the very effective design of ngn33r: https://www.thingiverse.com/thing:4859251other cam sizes & angles can be updated in the provided F360 files.

This is a top mount replacement for the stock front mount camera. It is modeled to be printed flat with no supports. Mounts to existing screw holes with no modifications required. ...It prints much easier and faster than the other designs I found.

This is a remix of the compact pocket case of [PROwyant](https://www.thingiverse.com/thing:3590819) which can hold not one but two 65 mm quadcopters such as UR65/US65/UK65/Mobula6/Mobula6 HD/Meteor65/etc. ...or similar ones.

Moblite 7 camera mount remixed. ... Fit the hole in the pin that protrudes from the frame