mmu2s prints 3d models

This is a comprehensive redesign of the MMU2S Print Buffer System to relocate the five spools directly above the printer, along with an innovative rear-mounted vertical buffer system. By doing so, it significantly conserves space, fitting neatly...

This is a redesign of the MMU2S Print buffer system to relocate the 5 spools above the printer and a rear mounted vertical buffer system. It saves a lot of space, fitting within a 56cm X 56cm (22" X 22") footprint. It just fits inside an IKEA Lack...

 Note, only model files (.AMF) are uploaded, no g-code uploaded for the upgrade.This is a redesign of the MMU2S Print buffer system to relocate the 5 spools above the printer and a rear mounted vertical buffer system. It saves a lot of space, fitting...

Just a quick way to test MMU2 functionality quickly. To make it work properly, you must preload all STLs together beforehand. If using Prusa Slicer 2.0, you will get a multipart object detected message and it will ask if you want to treat it as one...

There are different sizes and I chose the 45 liters scuba box to build my filament dry box.The first version of my dry box was perfect with MK3S+, but I designed this new version after upgrading to MMU2S to add build an air tight buffer. It will be...

I'm not sure I want this buffer, it's great and all, but I could really do without that spool holder attached to it, so I'm going to get rid of that part right now by making some modifications.

Prusa MMU2S Passthrough PTFE Adaptor Printed Parts for use with an M10 coupler like https://www.amazon.com/gp/product/B01IB81IHG/ref=ppx\_yo\_b\_widget\_title\_o00\_s00?ie=UTF8&psc=1 Category: 3D Printer Parts

Prusa MMU2S Passthrough PTFE Adaptor Printed Parts Designed Specifically for Use with an M10 Coupler Similar to the One Available on Amazon at https://www.amazon.com/gp/product/B01IB81IHG/ref=ppx_yo_b_widget_title_o00_s00?ie=UTF8&psc=1

 Just print it with layer height of 0.3 mm and attach it to the pointy end of a toothpick.The finger grip seen in the picture is from a different project (here). Check out my other useful prints at...

 Likewise for Extruder 3 you can use yellow filament first for the front and back insignias and then switch it out for white filament to print the white of the eyes.Switching filament in the MMU2S is a little challenging to do while the model is...

After printing, just heat it up with a hair dryer to get the right shape. I used an old deodorant bottle because it fit perfectly around my daughter's wrist - you can use anything that fits comfortably. ... I'm really looking forward to seeing some...

i designed it for my daughter, because her original Mia and me bracelet lost its color. After printing you have to heat it with a hair dryer and form. I use a deo bottle for forming, because it has the right size of the arm from my daugher but you...

Magic LCD knob two color printing without MMU2S for Prusa i3 MK3 & MK3S I used this version of PrusaSlicer:Version: 2.4.2+win64Build: PrusaSlicer-2.4.2+win64-202204251110Did you know that you can use the color change/ pause print function to insert a...

Magic LCD knob two color printing without MMU2S for Prusa i3 MK3 & MK3S I used this version of PrusaSlicer:Version: 2.4.2+win64Build: PrusaSlicer-2.4.2+win64-202204251110Did you know that you can use the color change/ pause print function to insert a...

Re-secure the latch and you are done. The Hardware: 1x 608 Bearing Per Filament (5 For A Full MMU2s) 4x M3 6mm Socket Cap Head Screws Per Buffer Section For The Pulley (20 For Zero Face Down, Zero Face Up, Tricid) 2x PC4-M10 Per Buffer Section (10...

I remixed the clip from 3dlyx to make it print-in-place, and strengthen the clip side a little bit. ... It's a bit difficult to pry open the first time due to tolerances, but then should swing freely.

That's why this remix fixes this minor flaw by replacing the wheel's inner “tub” with a chamfered arc, which is much easier to print, requires no supports at all and usually results in a pristine output. ...Print settings are the same as the original.

Print the cover with the PC4-M10 thread from the original Thing here: https://www.thingiverse.com/thing:3384288 I've been using this selector with a lot of success, but being able to combine this passthrough with the window should increase the...

Print the cover with the PC4-M10 thread from the original Thing here: https://www.thingiverse.com/thing:3384288 I've successfully utilized this selector, but combining it with the window should increase reliability even further. ...I also prefer the...

You've undoubtedly given up hope on perfectly printing with your PRUSA MK3 MMU2 because of those tricky perfect tip settings required? Discovering The Frog will breathe new life into your dreams of multicolor perfection, allowing you to finish each...

So I needed a solution for this, without printing the whole case.Here it is :-)You'll find version for mmu2s print as the pictures shows it, or for single print. ...Step file is also provided for further modifications.Print orientation changes as I've...

MMU2 test prints to show if any additional virtual colours are possible. Best results seem to be solid top or bottom layers (or perimeters) of semi transparent or light coloured filament, with darker colours behind. Using 3 primary colours + B&W...

MMU2 test prints to show if any additional virtual colours are possible. Best results seem to be solid top or bottom layers (or perimeters) of semi transparent or light coloured filament, with darker colours behind. Using 3 primary colours + B&W...

...TPU recommended but PETG is the next best thing. (PETG) May wear out over time and need to be replaced. 0.2 layer thickness Quality Smooth PEI print bed is probably better than the powder coated for these because you want the washers to be very thin.

... game mode called trouble in terrorist town and you are assigned roles of innocent, detective, and terrorist. I have 3 coins made for mmu2s prints if you want to make the inside a different color like I did. I didn't need supports on the bottom.

Just an simple conversion from the new Original Extruder Cover for the MK3s+ / MMU2S. Printed in PETG @ 25% infill. The PTFE Tube can reach the end from the extruder, it is easier to mount the filament. ... No more Loading issues.

Just an simple conversion from the new Original Extruder Cover for the MK3s+ / MMU2S.Printed in PETG @ 25% infill.The PTFE Tube can reach the end from the extruder, it is easier to mount the filament.No more Loading issues.

 Below are the author's notes from that page.  Notes:o   Stabilizes the tubes by keeping them evenly separated and snug.o   Because the tubes in the pathway are now all wider the filament sits “looser” (is that a word??) in the tubes and the filament...

 Below are the author's notes from that page.  Notes:o   Stabilizes the tubes by keeping them evenly separated and snug.o   Because the tubes in the pathway are now all wider the filament sits “looser” (is that a word??) in the tubes and the filament...