mmu2s assembly 3d models

As a cheap dry storage box for filament, IKEA Samla boxes (57x39x28 cm) are used by many. Sadly, when using a short piece of pipe to hold filaments, changing just one without disturbing the other three is very hard. Each Samla box can hold up to 4...

A part to replace on top of the mmu2s filament buffer to mount on a Skadis board.

I was asked for my MMU2s Remix of the Happy Planter Collection/ These remixes worked for me on the MMU2s and includes the following 3mf files for the original Happy Planter Collection for the MMU2s : 100 110

Like many MMU2S owners, I had a few issues with the PTFE tube setup - in particular, their "sandwich" clamp design that fails to put pressure on all 5 tubes. iwagner's excellent design worked great, but it was pretty easy to strip the modeled-in...

Update: After printing the buffer sides and assembling, I have experienced an issue where the filament does not feed through smoothly, I had a feeling that may happen! I have now redesigned the side buffer mounts and added the bearings to them,...

A sleek adaptation of the ingenious "Gravity Spoolholder for MMU2S" by Michal Fanta (https://www.prusaprinters.org/prints/10370-gravity-spoolholder-for-mmu2s) Video: https://youtu.be/Li5INzZ04JA Many gravity-reeling spool holders permit the spool to...

Request filed to utilize MMU2S as equivalent MMU2+1S unit.

Mount for MMU2s switch. You need to use 2 channel switch (you need to shut off GND and VCC). ...Use longer than original M3 screw to mount it.

Was tired of not knowing which tube to put the filament through on my MMU2s, so I made a simple 1-5 coding system.

Hold the MMU2S buffer on the right side of the IKEA lack enclosure and make it rotatable for easy filament change.

Like many MMU2S owners, I had issues with the PTFE tube setup - specifically, their "sandwich" clamp design that failed to put pressure on all 5 tubes. iwagner's excellent design worked well, but it was easy to strip the modeled-in threads with the...

For the original model and instructions, visit their Thingiverse post. Like many MMU2S owners, I had a few issues with the PTFE tube setup - in particular, their "sandwich" clamp design that fails to put pressure on all 5 tubes. iwagner's excellent...

This innovative design brings together the best of both worlds, creating a seamless upgrade for the MK3S with the MMU2s Sensor configuration. ...No more tedious disassembly required - this ingenious solution lets you upgrade your extruder without...

The switch to angled mounts requires shortening the bowden cable to the hotend, which necessitates adjusting the distance that the MMU2 feeds to the hotend. I didn't feel like recalibrating this, so I reverted back to the original mounts. If you...

You can chamfer the protruding part which goes into the extruder body so that it goes in smoothly.Extruder preparation: Extruder has to be prepared the same way as it does for the original chimney assembly.Adapter-printer-mmu2s (small orange block)...

I have a height restriction due to the limited space in the IKEA enclosure.The part is printed in PETG, prints flat without supports and makes use of the same M3 SHCS screws to attach to the MMU2S.(The selector on my MMU2S is also a combination of...

Splitter with "only" 5 paths for MMU2S. Used with 5 PC4-M10 and PTFE OD4mm ID3mm 2 versions available, Both versions are OK. ... If your filament tips are not perfect, please use the version V2.

This is just another PTFE comb/spacer for the MMU2(s). Its a quick and easy print and snaps right on to the PTFE tubes. I recommend printing in PETG. ...No supports required.

So I needed a solution for this, without printing the whole case.Here it is :-)You'll find version for mmu2s print as the pictures shows it, or for single print. ...Step file is also provided for further modifications.<br><br>Print orientation changes...

When I built the mmu2s, the cables were all over the place, I need away to organize the cables.This bracket screws on top of the mmu2s giving a place to wire tie the cables to for cable management along the back.  It uses the existing screw holes and...

Finger tighten only.Insert the existing M3x18 bolt into the opposite arm.Place the new tower assembly onto the top of the extruder, carefully sliding the trigger arm into the slot in the back of the assembly.Screw the assembly onto the top of the...

https://www.prusaprinters.org/prints/3151-mmu2s-tension-screw-retention-washer Every time I loosen up the two Idler tension screws and open the MMU2, one or both of the screws and their springs would fall out, bouncing around and playing a...

This is my modification of a MMU2S unit to work seamlessly with a Bondtech (Mosquito and E3D V6) Extruder.\r\n\r\nThis mod utilizes primarily four components:\r\n- BT_Sensor_Cover_PC4-M10_MMU2_up, secured with a square nut and an M3x6 screw for...

Since Bondtech doesn't provide modified firmware for the MMU2S, one simple workaround is to flash the Bondtech MK3S firmware first, followed by the Prusa MK3S-MMU2S firmware. Fortunately, the critical settings from the Bondtech firmware are not...

A no clunk adaption of the wonderful "Gravity spoolholder for MMU2S" by Michal Fanta.Video: https://youtu.be/Li5INzZ04JAMany of the gravity rewinding spool holder allow the spool to continue spin at the top, by jumping over the gears and making a...

You can easily screw M10 passthrugh fittings and use double sided tape to stick it whereever you want. This is remix of this object: https://www.thingiverse.com/thing:3233579 I have made a version with screws for lack enclosure:...

This ingenious device is designed to be installed atop the versatile IKEA enclosure featured in the Prusaprinters blog post, "MMU2S Printer Enclosure". My goal was to simplify the thread management process by reducing it to a single length, thereby...

Vile Spass beim Drucken Print instructionsMK3s-MMU2S IR-Sensor-Cover Wenn man eine MMU2S-Druck wünscht, ich habe auf der Oberfläche eine Pfeil integriert! ... Bitte beim Import der Datei, nicht vergessen den Körper zu teilen um beide Teile in einer...

I redesigned the Prusa mmu2s spool holder to make it easier to roll with. After searching for a straightforward solution, I decided to draw my own design. The result is a significant improvement that makes everything work much better now. ...I ended up...

I aimed for a straightforward method to detach the PTFE tubes from the Prusa MMU2S's rear end. Having an effortless way to remove these tubes significantly simplifies the process of loading filament and clearing jams. The material used doesn't make a...