mmu 3d design

They should work fine but I have not made a full clock with them, and they may get adjusted.This version has quite a few differences to the previous version:The face of the clock has been split into an outside ring (which holds the indicator design),...

It is build to match the wled Board from Serg74, but you can use other controllers, too. The case has the following features:The "Stick" is rotatable 355° without the need to rotate the case itself.The rotation has snap points to reach exact...

And to remedy this, in designing this monstrosity I have sacrificed everything: simplicity, optimal print orientations, even common sense. Still in terms of nerf “shotguns” this cross between a magstrike and a folding chair has much to offer. This...

This design is aimed at installing the bottle on the left side of the box. First you need to measure up to about 1.5 inches (3.8 cm) from the bottom, and then you start to drill a 1/4 inch hole in the side. The more holes, the better the airflow...

I've dialed in tolerances and rethought various different design details. And each time I've figured out a new way to do things, I've gone back to the beginning of the process and added those details and features to all the previous variants. So this...

I also added a filter with a different design of zig zag air ducts because of the fact that during printing the individual baffles could be separated from the print area. This makes them more stable. The grille and snap-in filter covers are optimized...

Loading in the middle position of the handle (measured from the top of the handle) 240g - The throttle is designed for installation in the side panel of the simulator or you can print a plastic base for it, the throttle with two buttons, one of which...

  Zach Freedman's work is available on Thangs, and you can find examples of his Gridfinity designs here and here, which are available under his MIT license.  If you like this model, or want to learn more about Gridfinity, you can check out Zach...

The motor supports designed for a 4-hole M3 mounting with a 25mm diameter can be used as feet or 7.5mm square aluminum tubes can be inserted. Mounting the camera on a rostrum towards the front should allow a comfortable viewing angle. Pay...

Most of the body parts are designed to require minimal supports however I recommend you set support threshold to at least 55 degrees at 0.2 mm layer height resolution. <h1>Wheels</h1> You can print either the wheels or the rims to use with...

After printing, I trimmed off the “elephant’s foot” on the tight fitting components using my jackknife (especially, the bottom of the trigger shoe, the front of the notch in the “A” selector pocket, the interrupter pin and its guiding slide slot).I...

Dremel Pillar Drill (Drill Press)&nbsp;Precision pillar drill stand for a Dremel giving a plunge depth of about 70 mm.&nbsp; Any Dremel that has the ‘standard’ 16 mm screw at the business end should fit but I’ve only tested this with the Model...

The construction costs are about 300€ and the construction time is about one day. contact email address ownplant@gmail.com Print instructions1.) Print out all parts and insert all thread inserts 33x "M4 Thread insert" they are all the same 2.) Saw...

MotivationI grow hot peppers as a hobby which also include saving seeds for the next season or for giving away to any one that likes to grow hot peppers.Now, preparing the seeds for drying can be tedious and even painful if you do not take the...

If you want, you can help me with designing inserts by donating here: https://www.paypal.com/donate/?hosted_button_id=J2YS7MREH8MU8 Hello, for those that don't know my ‘insert philosophy’ - I am creating modular inserts that are focused on reducing...

Simple bricks to play with or to integrate into other projects, designed to be easy to print, and easy to integrate in all other projects.Printing parameters:PLA//0.4 nozzle//0.2 layer height//0%infill//no support//brim All the parts in the files are...

DescriptionThis SherpaMicro extruder and carriage setup weighs 50% less than the stock Qidi extruder/carriage resulting in better print quality.The associated linear rail gantry files can be found here:...

The dimensions of the USB C board are critical to this design, if you do buy some please be sure not to cut the ears flush with the board, they need to stick out a little to lock the board in place. You will also need I believe, 5 pin 2mm pitch...

I made a one with some modifications and designed this pen to use with it. I think the pictures are clear enough to assemble the pen. Here are some details: First of all,** BOM:** 6mm copper rod as main welding rods:...

&nbsp;These projects can be used as a starting point to slice other model combinations.&nbsp;Spout Lid (Experimental):This is a test design for a spout lid to pour out parts. &nbsp;I'm not sure the usefulness of it yet so I only modeled it for the...

One designed for a multi material, or dual nozzle printer, the other for a single nozzle printer with a filament change required.The skybridges should be printed like the building pieces, with the open side facing down, &nbsp;and a raft is...

This is a brand new design, specially made for the Prusa contest, therefore photos with actual plants are missing. I will upload some pictures when the results are already visible.</p><h3>What you can grow as microgreens (or let it grow a bit...

This is a 100% original design by myself. I spent time learning Blender while making this. It's easier to learn a new application when you have a goal. I was using 123Design forever. This is a a BIG print. It is 18'' Tall, 15'' Wide and 6" Deep. ...

I do not have a way to lift the rear of an XC90 however as I have not been able to design parts for that yet. Here are some examples of expected results: <b> Top hat spacers only; <b> Gain 1.75-2" of lift. Mine are 25mm, for example, the Cross...

Reszta drobnych elementów, przewody, złącza itd....XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXA complete Led lamp for a marine or freshwater aquarium, this is the whole design of the led lamp with electronics housing and led lamps for the lamp you also...

with these, you can design your own arm or camera housing. Please notify me if you remix it or if you want your STLs to be uploaded here. ...I will credit...

- Replace the stock extruder mount by the filament sensor holder This work is based on the original Superfly extruder design by Mustcode https://www.thingiverse.com/thing:4841682...

The text and font of the squares can also be edited.This design has a few features to make it easier to print. Elephant foot is less of an issue because the bottoms of the internal squares are chamfered. The gap between pieces can be changed...

Then reassign the pin assignment at the limit switch according to the designations (G-> G, S-> S, 5V-> V). Actually, you can already test the whole thing: With the G-Code "M119" you can query the status of the end stops. But please do not drive...

A tailor-made rendition of the design available at http://www.thingiverse.com/thing:58001 was produced using the customization tool found at http://www.thingiverse.com/apps/customizer/run?thing_id=58001[^] [#]мьий мастер-класс по созданию...