mks sgen l v2 3d models

Here's My Design for the Ender 3 Pro: A Comprehensive Upgrade Guide If you're planning to upgrade your controller board on the Ender 3 Pro, this design is specifically tailored for the SKR 1.3 or MKS Gen L boards. While it should also work seamlessly...

It took a lot of measuring to get it right, but this case is now the go-to choice for SKR 1.3 and MKS Gen L boards. UPDATE: Some users have pointed out how snugly the print fits on the Ender 3 printer. Yes, it's a tight fit, and if your printer...

--- This is a remix of the (amazing!) #TeachingTech enclosure for the MKS Gen L. I remixed this project because I wanted a flush front (as opposed to a fan protruding out on its own) and I needed some practice with Fusion360. You shouldn't require...

Wanhao D3 Plus MKS/SKR Upgrade To connect the ribbon, I utilized an additional interface plate. ...I'm intentionally omitting the wiring for now as it's still a work in progress.

The enclosure is situated on the exterior of a box for general-purpose use, specifically designed to accommodate an MKS generator along with a protective covering for a 90mm fan.

MKS version 1.1.9 and SKR 1.3 version 2.0.x. Change Log 2019-07-16 - No changes - just confirming SKR 1.3 fits nicely (and it's a nice board :) ) I made a Prusa i3 mk3 Clone - with a MKS Gen L as a mainboard so I needed a case for it (should also...

Name says it all: Rapide Lite v2 Extruder L Bracket Made in collaboration with Holga Mods

......They include two mounting supports for fixing the box under a table or workbench and a housing that integrates the original Tornado screen and an MKS TFT 32 touch screen. ... Just extend the two connectors of the original screen to the right length.

Low profile version files: https://www.thingiverse.com/thing:3502425 Cable chain: https://www.thingiverse.com/thing:2920060 Supports: YES I started with low profile version, but it barely fit MKS and cabling was a mess. So version 3 is based on high...

Later on, I changed my mind once again, but had already designed an adaptation of the bottom plate that houses the MKS board and accommodates an Arduino Mega. This setup indirectly supports any ramps board. The design was specifically planned with...

I started with a low-profile version, but it was too tight for my MKS setup and the cables were all over the place. So I moved to a high-profile design, which gives me extra space to cool my TMC2208 motor driver. I remixed both control boxes to fit...

... integrated seamlessly with the main case. To ensure a proper fit, it's essential to trim the hole for the USB cable on the MKS case and also trim the lid of the RPI case where the fan is located. ...I'll continue to update this design as it evolves.

The MKS side features an external fan blowing in, while the OrangePi side boasts an internal fan blowing out - a genius move to keep my TMC2130 drivers from overheating. - I've tweaked the left box to snugly fit my trusty OrangePI PC. - By shaving...

Complete case for board maker's general L or board maker's general 1.4. Top part of the cover features a magnetic mount. Magnets used are 4x2mm in size. ... Magnets can be found at the following link:...

I started out with an MKS-TFT 3.2 but scrapped it for the reprap full graphic display because it was using too much serial line bandwidth. My new setup has fystech tmc2130 drivers in spi mode, so I needed active cooling for the stepper drivers. This...

Fan duct and matching fan grille for mounting a fan directly above a GEN_L board. When used with an 80x80x10 mm thin fan, the design fits right inside the A5 JGAurora with enough headroom for the Y-axis gantry to pass over. Required parts: *...

upgrade the printer's hardware box

I printed this for my Anet E12 to fit snugly inside its control box and the USB attachment in one convenient location. The print was almost perfect, with only a tiny margin of error - just a hair off from where it should be. I did have to make a...

Its for 1 40/40 fan and 1 30/30 fan, so you have a better cooling for your drivers. ... I draw it, cause I found some fans laying around, and these both were the only ones that fitbperfectly.

The General Officer Commanding (GOC) 6 Division Major General Musa is leading the charge to bring peace and security to Maiduguri City. ...The GOC is determined to crush Boko Haram's stronghold in the city, using his fanatical zeal for justice as...

Print settings: Infill at approximately 40% Print speed: 40 to 60 mm per second Layer height: 0.2 to 0.25 millimeters Check out my YouTube channel: https://www.youtube.com/watch?v=J5BzorV7rh0&t=240

Chassis with inputs for drivers, sensors, etc., with cover for ventilation

This is a remake (not a remix) of the front frame of rammii's controlbox. Since we didn't get access to the F360 files i had to redesign this from scratch. This Frame features an internal cutout and external hole for the default speaker (no more...

I adjusted the mounting hole by moving it 5 mm over to one side. However, the main challenge was that all the holes designed for the board were drilled at 3.2mm in diameter, which is significantly larger than the original screws could accommodate. To...

In SolidWorks 2018, users can easily generate and export STEP files for sharing 3D models with others. The STEP file format is widely accepted and provides an accurate representation of the model's geometry and features. To create a STEP file in...

Assembling the system involves carefully crafting components independently without the aid of supporting mechanisms. Meticulous attachment ensures seamless bonding between upper and lower assemblies by expertly threading the M5 screw to merge them...

Collaborate with me and help my channel grow by subscribing to my YouTube channel at 3dmakeres. You can also support my work financially through a donation to my PayPal account, 3dmakeres@gmail.com. To connect your USB devices, use the USB port...

This is a complete reimagining of rammii's controlbox front frame. Due to our inability to access the F360 files, I had to start from scratch. This new frame boasts an internal cutout and external hole for the default speaker, eliminating the need...

Just mounted it on LACK table, flipping it over to face downwards.

This tidy solution tames the tangled mess of cables that comes with using TMC2130 driver boards via SPI. ...It gives your setup a polished look, while also adding a touch of organization with small 4-inch zip ties that keep everything neatly in its...