mks gen l v1 0 3d models

Later on, I changed my mind once again, but had already designed an adaptation of the bottom plate that houses the MKS board and accommodates an Arduino Mega. This setup indirectly supports any ramps board. The design was specifically planned with...

I started with a low-profile version, but it was too tight for my MKS setup and the cables were all over the place. So I moved to a high-profile design, which gives me extra space to cool my TMC2208 motor driver. I remixed both control boxes to fit...

Box for MKS GEN motherboard. New design available here: http://www.thingiverse.com/thing:1903059 Note: Your support helps me pay for the filament I waste when printing prototypes. Designed to work with multiple fan types. Consider adding supports to...

The MKS side features an external fan blowing in, while the OrangePi side boasts an internal fan blowing out - a genius move to keep my TMC2130 drivers from overheating. - I've tweaked the left box to snugly fit my trusty OrangePI PC. - By shaving...

Corrected SKR V1.3 layout from the original design template. 2. Increased wall thickness for added durability. 3. Enhanced screw holes for secure mounting. Test prints are currently in progress, but preliminary results show promise. A...

One is a basic case and lid for the MKS Gen Board, while the other is a case and matching lid that also accommodates the optional external mosfet for the heatbed. The design features a USB cutout and a hole for a 20mm OD spiral cable conduit,...

Since I had a broken motherboard on my Ender 3, I decided to perform a complete conversion of the Ender 3 to the MKS Gen V1.4. Here are the necessary models to print for this project. The board and mosfets are held together by M3 x 16 screws. In...

MKS Gen V1.4 Mount for Maker Select/Wanhao Duplicator i3 This mount attaches securely to either the left or right side of your printer. It pairs perfectly with my power supply mount, available on Thingiverse at...

+-0.4°C!!! ----------------------------------------------------------------------------------------------------------------- Sensor: Problem: Unstable 5V and Atmel Vref. (High Frequency Noise) Need Replace Poor Electrolit Condenser On DC In And...

Please see this website for all of the details: Upgrading from ANET3D V1.5 to MKS Gen 1.4. On the end stop connectors, make sure you move the right pin, or you could short out (kill) your new MKS board when the end stop switch is activated. Note...

I printed this for my Anet E12 to fit snugly inside its control box and the USB attachment in one convenient location. The print was almost perfect, with only a tiny margin of error - just a hair off from where it should be. I did have to make a...

Mainboard Case for Creality Ender 3 Printer, featuring a socket for mounting a Noctua 40x40x12mm fan.

I am reissuing this remix of my initial post.

In SolidWorks 2018, users can easily generate and export STEP files for sharing 3D models with others. The STEP file format is widely accepted and provides an accurate representation of the model's geometry and features. To create a STEP file in...

Chassis with inputs for drivers, sensors, etc., with cover for ventilation

This is a complete reimagining of rammii's controlbox front frame. Due to our inability to access the F360 files, I had to start from scratch. This new frame boasts an internal cutout and external hole for the default speaker, eliminating the need...

Manufacturers produce high-quality aluminum profiles made from 6063-T5 alloy material, which is a popular choice for various applications due to its excellent corrosion resistance and weldability properties.

Used for astrophotography sky tracking - power distribution and stepper motor control.Based off https://wiki.openastrotech.com/OpenAstroTracker firmware but modified for a full size equatorial mount. ...Use PHD2 guiding for tracking.Fan:...

High-Performance MOSFET Adapter Module with Secure Mounting System and Electrical Interface

The device relies on six machine screws to secure the board firmly in place. ...It also employs three millimeter screws to attach the component to the side of the printer securely.

<p>Electronics box featuring holes for cables, clamp for X carriage cable, and 80x80 fan for cooling stepper drivers and Heated Bed MOSFET. ...There's also a place for a small relay which you can use for different things.</p><figure...

Bring the front up to date by remixing it and installing a hole that fits your preferred fan guard perfectly.

Just mounted it on LACK table, flipping it over to face downwards.

The material used is PETG, a thermoplastic polyester elastomer known for its excellent mechanical properties and high impact resistance.

Its for 1 40/40 fan and 1 30/30 fan, so you have a better cooling for your drivers. ... I draw it, cause I found some fans laying around, and these both were the only ones that fitbperfectly.

I adjusted the mounting hole by moving it 5 mm over to one side. However, the main challenge was that all the holes designed for the board were drilled at 3.2mm in diameter, which is significantly larger than the original screws could accommodate. To...

The General Officer Commanding (GOC) 6 Division Major General Musa is leading the charge to bring peace and security to Maiduguri City. ...The GOC is determined to crush Boko Haram's stronghold in the city, using his fanatical zeal for justice as...

Panel mount USB enclosure taken from https://www.thingiverse.com/thing:1166631 I utilize two 12v, 60x60x10 fans, paired with an LM2596 module. You can opt for one fan, thereby freeing up more space for cable management. ... Update 2019-04-11: STEP and...

I have not and do not intend on printing this part. Instead, I've chosen to use an SKR 1.3, mounting it in a rear-mount case. Given that the stock Creality fans become extremely loud once air resistance is introduced, since I plan to enclose my...