mk3s fan shroud 3d models

So far I usually used half of the fan speed default values used in Prusa Silcer and worked great.A picture of the overhang test shows: left stock mk3s+, right this fan shroud. Printed with same filament spool and same gcode. ...The overhang test is...

Modified stock fan shroud to work with the vulcano hotend.

Alternative fan shroud for MK3S+ direct replacementFeel free to share and comment so design can be improved.Redirected airflow to the bottom for better part cooling.PINDA sensor clearance.Silicone sock compatible.Uses all stock hardware (M3 threaded...

I'm adapting codiac2600's concept to match the specifications of an MK3S, and I'm currently conducting tests to assess whether this modification results in any noticeable improvements.

KP3S 3.0にBMGエクストルーダーとBltouchをマウントします。 TrianglelabのDragon Hotendに4010ファンを装着します。 Prusa i3 MK3S+のファンシュラウドを利用していますのでこちらからファンサポートとファンシュラウドを入手してください。 print-fan-support.stl fan-shroud.stl...

I wanted to use the fan-shroud of the Prusa I3 mk3s+ model, Since I already own an I3 mk3s printer, I created a new modeling file by directly measuring the approximate location of the shroud. The result of the application is somehow successful,...

https://www.thingiverse.com/thing:3913249 https://www.thingiverse.com/thing:3599905 https://www.thingiverse.com/thing:3603004 https://www.thingiverse.com/thing:2425783 However, I didn't like the set of Fan-shrouds provided, and even touched the...

Simple hexagon shroud for your Delta-P fan modded MK3S+ 5015 part fan.Had part fan crack slightly when tightening too much and screw head going in the fan hole, so I created should for the fan.Fully support free.Optimized dimensions for 0.2mm layer...

So i hade a bit of problem with the print fan shroud starting to get soft and dropping down on the right side (that is unsupported) when i was running print with huges first layers so the print fan was not on for a long time. I grabed the STL from...

I reinforced the mounting holes on both sides of the design, ensuring a rock-solid connection every time. ...My initial version began to loosen on the right side after several prints, but this modification has resolved that issue completely.

M3 DIN562 square nuts are difficult to find in North America from retailers like Amazon, but M3 square nuts meeting DIN557 specifications are very easy to come by. Because of this, I slightly modified the original Prusa i3 MK3S print fan shroud to...

R3 LED shroud -> https://www.thingiverse.com/thing:3300614 https://www.thingiverse.com/thing:3694984 (this one whitout LED) R6 to R4 shroud -> https://www.thingiverse.com/thing:4698884 English: Today I hand in my R6 to R4 LED air nozzle, which I...

Expanded the opening to accommodate a TH3D 5015 blower seamlessly. ...Removed the slot previously reserved for the notch on the fan, as the TH3D fan's notch is positioned higher, leaving only a slight gap. ...The new design ensures a snug, secure fit.

Volcano fan shroud for MK3s+This is a meshmix of the mk3s+ fan shroud to work with Volcano Hotend.I have not found a volcano shroud for the mk3s+ so I remixed one from the original Prusa fan shroud. print in ASA or ABS! ...(PETG and PLA will...

UPDATE 08.July 2019 ------------------------------ A friend of mine asked me to modify the fan-shroud so it's 1mm lower, and according to him, it performs even better. So I decided to upload this version for everyone to use. While remixing the first...

Lowered the bottom face of the shroud 0.6mm to accomodate a silicone sock and added some baffling to improve side flow.   The fork tips are connected to the print support for better printing with PC to help them adhere to the print sheet.

Posted here with conspicuous credit. This fan shroud was designed with Autodesk CFD to create better airflow around the nozzle of the Prusa MK3s. Airflow around the Front and both sides has been equalized and pointed more at the tip of the...

I created this modified Fan Shroud to enhance printability on FDM Printers. Bridges print better than 90 Degree Curves in the Air. As seen in the original Shroud's first picture, it is positioned inside a 90 Degree Curve in the Air. This...

modified the right mounting fixture specifically for MK3S+ fitment to help keep the fan duct level. 3. Added mounts for 3x 3mm LEDs right at the nozzle tip 4. Added chamfers to reduce weight where possible ** PLEASE SHARE YOUR PRINTS, AS I'M NEW...

Plus the fan shroud "glows" during the print, which is a pretty cool effect I think.      4. Some soldering needed to connect the 3x LEDs in parallel, and route the wires with the main cable bundle to the Einsy board and tapped...

Plus the fan shroud "glows" during the print, which is a pretty cool effect I think.      4. Some soldering needed to connect the 3x LEDs in parallel, and route the wires with the main cable bundle to the Einsy board and tapped...

I also minimized the middle opening, cause in my opinion most of the air just streams down and is not used for cooling.In my testing against the stock shroud, overhanging and bridging looks way better.I´m not sure, if the side openings are big...

... shroud, overhanging and bridging looks way better. I´m not sure, if the side openings are big enough, so please comment your thoughts or remix the thing as you like. There is also a modified shroud for the MK3S without the second mounting point.

I also minimized the middle opening, cause in my opinion most of the air just streams down and is not used for cooling.In my testing against the stock shroud, overhanging and bridging looks way better.I´m not sure, if the side openings are big...

There is one solution prepared by goldbird3: https://www.printables.com/pl/model/199028-prusa-mk3s-rhd-fan-shroud-duct-revc but it uses the original fan mounting point on the Prusa extruder cover, which forced to add a connector for fan mounted with...

I have not found a suitable modification to the excellent print fan shroud created by RH_Dreambox: https://www.thingiverse.com/thing:4376765to suit the Mk3S+ (the latest Prusa extruder design marked R6).There is one solution prepared by goldbird3:...

... So I can quickly switch back to the original fanduct.Oh, and you have to glue the two fanshrouds to your fans so maybe get anoter fan without a shroud to swich back.Sadly the fans now have so much power that they cool down the heating block easyly.

Based on the original Thing from K_Lab - thanks for the source Fusion 360 files: https://www.thingiverse.com/thing:3533859 and the remix from Theo Tinjum: https://www.prusaprinters.org/prints/34393-prusa-mk3s-low-noise-fan-shroud-45deg-angle I...

The extra thickness and reduced bolt hole sized eliminated the need for washers and correctly aligned the shroud with the fan intake. The base is now significantly stiffer with a negligible increase in weight. Two M3x25 or M3x30 bolts (there are...

The user adjusted the printing angle to 45 degrees, ensuring the Shroud wouldn't collide with the Print bed on their MK3S. ...This modification is a revised version of the original design found at thingiverse.com, specifically thing number 3533859.