mk3 cable 3d models

The Shaft is now prepaired to hold a nut and the cableholder is modified to guide the cable a bit better. I've used as Basecase the Case from hackoholic and his Cammount. Update 30.03.2018 I've added a Version to mount the Pi on the right front side...

and all the times I had to cut and then put back the Zip Ties, that group the wires of the various components. With this system I can have access to the wires of the extruder components without having to change all the times the Zip Ties. Another...

I needed a low-profile 90 degree cable cover for the Mk3 that would allow it to fit in an Ikea STUVA cabinet. I couldn't find one that worked and accommodated ring terminals, so I designed one, instead. Perfect fit using 90 deg. terminals from...

So even though this is not technically a remix, credit where credit is due for the inspiration for the design. This is a slim 90 degree heatbed cable cover for the Prusa MK3 / MK3s. It is inspired by tcurdt's andled heatbed cover, but is completely...

This slim 90-degree heatbed cable cover is designed for Prusa MK3 / MK3s printers and was inspired by tcurdt's andled heatbed cover. However, it has been completely redesigned to make it slightly thinner, easier to print, and incorporate proper...

Here is my version of the 90 degree heatbed cable cover for the original Prusa i3 MK3. I recently received it and it's absolutely wonderful. I decided to put it inside my IKEA Lack case, which I built thanks to a very good tutorial published by...

Hello friends!Here is my version of the 90 degree heatbed cable cover for the original Prusa i3 MK3. I recently received it (and its wonderful), and I put it inside my IKEA Lack case (I previously made thanks to Prusa who published a very good...

Here's my take on the 90-degree heatbed cable cover for the original Prusa i3 MK3. I recently got it and I'm thrilled with how it turned out, so I decided to install it in my IKEA Lack case - a project I started thanks to Prusa's excellent tutorial...

I trimmed the corners to be at 45. The remaining parts can be grabbed from their respective original thing (cable clamp end, camera case, etc). [Edit] Added cable clips to help contain the unruly ribbon cable. 11mm goes on the fattest part of the...

I was looking for an upgrade of the original Y-Rod holders that are shipped with the MK3/S and came across the one from MarcoZ76 which was going in the same direction I had in mind. ...However his Version uses a screw and I wanted it to be compeltely...

Cable Cover Sits at a Sharp 90-Degree Angle. ... Tightened Up to Minimize Space Used Along the Y Axis Movement. The Ground Cable Forms a Perfect U Shape, Allowing It to Slide Beneath the Heatbed Smoothly.

Introducing the PIcamcableclamp :) This is a remix/combination of two things: The main support arm comes from: https://www.thingiverse.com/thing:2956323 and the cable clamp is from: https://www.thingiverse.com/thing:2887361 I made one change to...

Much nicer look with hex heads on top.No modifications are required to heat bed/cables in order to fit this cover on the heat bed with screw connectors. This has been tested on a heat bed with screw connectors. This does allow clearance for the hot...

Didn't like to bend the flat cables into the extrusion, so later I prepared these clips. ... The support clips below the extrusion so it doesn't interfere with the Y-axis movement, and have a thin lip for ease of installation/adjusting.

The Original Prusa i3 MK3 X-Axis Motor Cable Strain Relief Features a Built-In Catch on the Motor Flange for Added Security and Reduced Wear.

Original Prusa i3 MK3 X-axis motor cable strain relief with added catch on motor flange.!Not compatible with Bear Upgrade!originally: https://www.thingiverse.com/thing:3433554remixed from: https://www.thingiverse.com/thing:3216603Print...

While building the Ikea Lack enclosure for my MK3 I found that the connector cover proposed in manual is too high. Here is my take on the 90 degree connector cover</p> <p>Black (Negative/Ground) wire has to be turned to the left and bent to go under...

While assembling the Ikea Lack enclosure for my MK3, I discovered that the provided connector cover in the manual is woefully inadequate. To correct this issue, I created a 90-degree connector cover that better suits my needs. To install the new...

https://www.aliexpress.com/item/Anti-interference-high-quality-short-20cm-A-Male-to-B-Male-USB2-0-Printer-Cable-Line/32809052856.html I recommend buying the original Raspberry power supply, 5V 2.5A. I tried using other PSU's and had a power alert on...

... included in this remix. ... No modifications to heat bed/cables are needed to fit this cover on the heat bed with screw connectors. This has been tested on a heat bed with screw connectors. ... You will need: - Three M3x12 screws - Three M3 nuts

I connected the Raspi to the printer using a short Usb cable that I bought in Aliexpress....

I printed a flipped version of the PSU mount and mounted it to the side of the enclosure instead of the back and then cut out a small port hole for the PSU cables to go through. I didn't want the cables to rest against the cut out part of the plexi...

My goal was to keep the cables from coming into contact with the cut-out section of the plexi. To achieve this, I created a custom cable management piece. The plexi needs to be trimmed to 14mm wide and 18mm tall with a rounded top edge. ...Using my...

If you are even more impatient, go to the Filament Settings tab, choose Cooling, make sure you're in Expert mode, and clear the "Slow down if layer print time is below:" field - this will drop print time to 26 minutes!Print instructionsOptimized for...

For other Prusa MMU projects: https://www.thingiverse.com/AbeFM/collections/abes-mmu2-stuff After adding connectors to my fans, thermistor, and heater, I encountered frustrating issues with broken wires from the thermistor when working on my...

This cable tidy will get rid of the annoyance of that dangling USB cable going to your phone. Simply loop back the cable on itself to give the right length, slip it into this and drop it into the small tray under the heater controls. ...No sticky tape...

This feature enables you to secure the X-axis wire guide, preventing it from shifting out of position. Additionally, a revised motor component will be introduced, which combines the original part with an adjustable guide arm for enhanced...

I had an issue with the original model when my support failed, so instead of using supports again I added a brace so the model can be printed without supports.