mk10 extruder upgrade 3d models
131177 3d models found related to mk10 extruder upgrade.cults3d
This is a heavily reinforced extruder arm and body. It is designed to be easier to print, and has removed the narrow point just above the idler pulley to to distribute stress better. Goals were to: 1) Verify dimensional accuracy. 2) Beef up the...
thingiverse
This heavily reinforced extruder arm and body is designed for easier printing, featuring a streamlined design that eliminates the narrow point just above the idler pulley to distribute stress more effectively. Key objectives were achieved: 1)...
thingiverse
I revised the problematic STL file to resolve an issue, also enhancing its overall resolution.
thingiverse
After upgrading my Tronxy P802MA with a high-performance Mk10 extruder upgrade from AliExpress, I installed a MicroSwiss all-metal hot end and throat. However, the heat soak issue persisted, so I needed to find an effective way to cool the metal...
thingiverse
Improved fan extruder spacers for the MK10 extruder provide a significant upgrade over stock components. By increasing the size of the spacers, better supports are enabled while ensuring the fan sits perfectly square on top of the heatsink. This...
cults3d
Nozzle 0.4, layer 0.12 This adapter allow owners of MK10 extruder (like the Titan on Tevo Tornado) to use a M6 PTFE, like the capricon one photo.
thingiverse
Nozzle 0.4, layer 0.12\r\nThis adapter empowers users of MK10 extruders - such as those found in Tevo Tornado machines, featuring the Titan - to seamlessly utilize an M6 PTFE setup, akin to the Capricorn model showcased in a provided photograph.
thingiverse
The MK10 Extruder is paired with a V5 Bowden system, along with a 30x30 fan and a 40x40x20 blower fan. This setup is compatible with the carriage at the following address: https://www.thingiverse.com/thing:2514659 (JackWaterfall). A video...
thingiverse
Flex MOD MK10 Extruder Frame: A Modified Design for Improved Performance This design is a modified version of someone else's work, tailored to accommodate a 4mm OD PTFE tube between the frame and thermal break, preventing flexible filament binding...
thingiverse
Common MK8/MK10 extruder users often encounter problems using flex filament due to fixed spring tension and backlash in Teflon tubes when utilizing FESTO systems. This design addresses these issues by allowing either M4 nuts or 5.5-6.0mm holes to...
thingiverse
I find if you press the lever too hard, you leave a small gap for the filament to leave the extruder from under the roller and if you keep pushing the filament after the resistance, you will see the filament come out the side of the extruder under...
thingiverse
This revised CR-10 FU knob has a more natural appearance and is simpler to print due to its smoother transition at the wrist. ...It seamlessly fits onto MK10 Type extruders such as the CR-10, Ender-2, or Ender-3.
pinshape
Whether you're printing complex models or producing high-quality prototypes, an MK10 extruder is sure to deliver. CR-7 extruders are designed with ease of use in mind. They have a user-friendly interface that makes it simple to adjust settings and...
thingiverse
Most MK8/MK10 based extruder units share a common issue: their biggest part is a single piece, and what if you mistakenly purchased an extruder unit with the wrong orientation? This problem could lead to significant delays in your project. The...
thingiverse
I suspect this will work for other extruders with similar designs that utilize the same size spring, although I have only experience with the MK10. Print Settings: Resolution: 0.1 - 0.2 Infill: 100% Notes: ...
thingiverse
e3d V6 Hotend Mount for MK10 Extruder. Bill of Materials: 2 x M3x25 Socket Head Cap Screws 1 x e3d V6 Hotend Note: Since I had M3x30 screws instead of the specified M3x25, I needed to add an extra part (mk10_e3d_ct) to ensure a secure fit. ...The final...
thingiverse
So, I designed one from scratch based off the stock MK10 extruder that came with my plus. Alignment and thickness are correct and I've raised the spring nipple plate up 1.5mm for increased tension. Install is fairly simple. Cut a 4mm piece of PTFE...
prusaprinters
IN THAT WAY IT IS AVOIDED COMPLETELY ANY FLEXION OF THE WHOLE SYSTEM. Currently, using nozzle 0.6 I have retractions between 1.6 and 1.8 mm at 50 mm / s Print instructionsUnassociated tags: extruder chiron, mk8 chiron, mod chiron Category: 3D Printer...
cults3d
Extrusión semi-directa para Anycubic Chiron usando el hotend mk8 /mk10 se utiliza el mismo carro original, pero HAY QUE CORTAR EL VÉRTICE DONDE SE ATORNILLA LA CADENA QUE LLEVA EL MAZO DE CABLES, de forma que la parte superior del carro quede...
thingiverse
Semi-direct extrusion for Anycubic Chiron using the hotend mk8 / mk10. The same original X carriage is used, but the vice must be cut where the chain which carries the cable harness is screwed, so that the top of the carriage remains completely...
thingiverse
For all CR10 owners with original Extruder on printer, if you experience under-extrusion / delamination, a possible solution may be to extend your Extruder Spring. Disclaimer!!! Do it at your own risk! Damage may occur to your printer! As soon as...
thingiverse
Upgrades to its original form make this a stronger component altogether. The new model operates more efficiently with clearer instructions. Layer thickness optimized for maximum quality: 200 microns. For durability and lightness, a default infill...
thingiverse
This compact modification takes the place of stepper motors on a MK10 dual extruder's heat block, and it may also work on a MK10 single extruder setup. To install it successfully, simply tap the hole for an M10 push fit connector. Printing at 50%...
thingiverse
It's a UP Afinia EXTRUDER MODIFICATION that I've upgraded a bit further so it can use a skateboard bearing and has less flex with the shroud, resulting in improved performance. ...However, the geometry is a bit messy, so I'd like to optimize the STL...
thingiverse
MK10 dual extruder PTFE cutting jig Flashforge, CTC I made this, as there are a couple of other tools about on thingiverse that aren't the correct size. I found using the other versions the nozzle would consistently leak. ... This tool has been made by...
thingiverse
This is a comprehensive system for cooling the MK10 extruder and print piece. I believe it will also be beneficial for other printers that utilize the MK10. The name "Scolopendra" was chosen because its design resembles a scolopendra head. A video...
pinshape
I've designed an all-in-one cooling system for the MK10 extruder and print piece. This setup is also beneficial for other printers that utilize the MK10, so I'm sharing it with you. The system's unique design inspired me to name it "Scolopendra," as...
thingiverse
An omnidirectional toroidal vane cooler for the MK10 extruder module of the ReDuplicator i3 MK3x can be found at: https://www.thingiverse.com/thing:2686588 The objective was to provide airflow from all sides, unlike the back-heavy cooling of the...
thingiverse
Prusa Type Radial Fan Holder for MK10 Extruder. No Extra Hardware Required. This holder secures the extruder fan in place without needing additional hardware such as bolts or nuts. The chassis is fastened to the extruder using the existing fan bolt,...
prusaprinters
Prusa type radial fan (50mm) holder for MK10 extruder. Doesn't require additional HW (bolts or nuts) Chassis will be fasten with the extruder fan bolt (remove the 10mm nylon pipe). Additional support is given by the edge of aluminum extruder bracket....