mjolnir mark iv 3d models

Beside the KV-1E in the picture is a captured KV-1 tank previously marked and used by the Germans, which signifies its influence even on the German army. All written materials and blueprints for the KV-1E mentioned in this post are sourced from...

I then marked the GND, VCC, SCL and SDA pins on the back for easier hookup later.   If you use pin headers with connectors, you will need to bend the pins to about 45 degrees on the back of the plate for wire clearance.  Test fit...

 Using the measurement tool:Stick the raw rod in the tool till it bottoms out.Mark the rod where the open end of the tool is, this is your cut line!Remove the measuring tool, and cut the Hex rod.  <i>(Those portable bandsaws make this an easy...

You should stop using the battery when the voltage gets to 15V (3V per cell)Glue gun runs for about 4.5 hours on a 5Ah battery by the way.Changelogv1.1There are now 2 versions of the adapter plate and connector column with place for a voltmeter.Added...

NOTE: Using this screw is likely to mark the hotend. 8. You will need to either solder the two blower fan cables together and crimp on a new JST SM 2.5mm female terminal, or make a 2 male to 1 female JST SM cable so that the single wires for the...

Marks advice from his years of studying the original studio model has drastically improved the quality of these models. This kit supports the following variants of the Excelsior: Mk 1 – The NX 2000 as seen in Star Trek III. MK 2 – The NCC 2000 as...

I repeatedly installed the bearing to be snug enough that it would scratch the steering tube, then removed the bearing and sanded just to remove the scratch marks it left behind. This way the sanding wouldn't make the steerer egg-shaped. After...

Try to get an Oak dowel if possible since there is a lot of stress on the star wheel axle.&nbsp; An easy way to cut sections of dowel is to mark the desired lengths, put a knife blade exactly on the mark with the blade 90 degrees to the dowel and...

Get Steam Link and install using the first post here: https://steamcommunity.com/app/353380/discussions/0/1743353164093954254/ Once that is done in your terminal type or copy these lines exactly: - touch ./RetroPie/roms/ports/Steam.sh - nano...

If you are screw-mounting the assembly, first install four of the bit-holders on opposite sides of the wheels, and then use the partially assembled holder as a guide to mark the location of the mounting holes; you can then mount the partial assembly...

You should stop using the battery when the voltage gets to 15V (3V per cell)Glue gun runs for about 4.5 hours on a 5Ah battery by the way.Changelogv1.1There are now 2 versions of the adapter plate and connector column with place for a voltmeter.Added...

The marks L and R on the bottom of the light tubes are seen from the front, from the light side! In my case I have taken shorter screws (4x Ø m3x10mm). They are very short in length. Therefore, I recommend to take longer screws. Step 6 - Preparing...

You make and use these adapters on your own risk.As far as Makita batteries go (star and non-star marked). I've been able to discharge them all the way down to 10V (2V per cell) without them cutting off. This is far below usual cutoff voltage, which...

Only glue along the inner step (marked red in the photo as an example) to avoid glue squeeze-out towards the outer edges.I used the optional tools to clamp the felt in place whilst the glue set.I only did one side at a time so that the glue would be...

You can use the injection molding marks on the inside of the black part and line up as best you can from the outside for two of the holes, third one split the difference between two marks. Feed the two wires up the tube and solder them to the two...

The method I used was, marking the cut in both sides of the acrylic with a sharp blade and applying even pressure until it broke to the line. Be careful to apply pressure especially in the middle on the line. Some small filing may be needed...

Onto the PC supply: PC Running Power Factor: 0.74 PC Running Watt Average: 116 PC Heating Watt Peak: 192 PC Running VA Average: 147 PC Heating VA Peak: 194 Right off the cuff the power factor while running is markedly better which results in much...

If you want to use the hardware I intended this to use:Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge)Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

Take your time and wait until the glue has cured completely!remove the placement helper construction from the cyclones and place it on the lid of the hobbock like shown in picture #7.Use the marker to mark the holes for the cyclones and cut them out...

The eyes were slightly too small, and the mouth was too tall.&nbsp;For the eyes, it was more than likely a measurement issue where our rulers weren’t calibrated to each other, which is something we found in the sketching process and presented a...

The "cylinder" is designed to be replaced if other sizes are needed, and the STEP files are included which should make this easy to remix or add different drill sizes. The base and fence have marking lines spaced at 10mm intervals on the base and...

(yellow marked fields) Since I was using PETG and the surface (at least for me) was not as good as I would like, I used the Fuzzy skin Oprion (Prusa Slicer / Super Slicer). The result speaks for itself (but you have to do this even on the test part...

Firmware from this project - https://www.thingiverse.com/thing:3463845 And again, many thanks to Mark, the author of the firmware. This time, he helped me change the controls and add subroutines to his firmware to control the servo drives of the...

The easiest way to add 3 units is by printing a Gen2 Rail Double Rail and a Gen2 Rail Single.Gen 2 Rail SingleDownload HereGen 2 Rail DoubleDownload Here&nbsp;• Use templates to mark the hole locations on the surface you are mounting the desired...

The marks L and R on the bottom of the light tubes are seen from the front, from the light side! In my case I have taken shorter screws (4x Ø m3x10mm). They are very short in length. Therefore, I recommend to take longer screws. ---- Step 6 -...

Directed by Guillermo del Toro, Pacific Rim introduces some incredible colossal sea monsters, one of which is Otachi - a large and heavy Category IV Kaiju. The “Swiss army knife of a Kaiju" was inspired by the dragons of Chinese mythology, she can...

Necronom IV by the renowned Swiss artist laid the unrivalled foundation for the onscreen incarnation of evil and Giger’s trademark biomechanical style defined the image of the cinema's most terrifying extraterrestrial.Inspired by Giger’s otherworldly...

There is also a box and a barrel in the star fighter’s assembly kit that you can print as many times as you prefer in order to recreate the fan-loved docking bay scenes from Star Wars: Episode IV – A New Hope. Being a combination of a starfighter and...

Use that distance to mark the wall and mount the clips. The box can then just snap into the mount.The parts can all be printed without supports but the Plug Holder works better if it has a support under the retaining protrusion. Without the support...

NOTE the polarity of the LED, many will have tiny "+" and "-" markings on the ends of the leads, some have a small notch on the + side (see pics). This now becomes a bit tricky - The BODY has hole in the side leading to one side of the LED, and...