miss fortune 3d model

1 slot for a pair of Kitchen shears and 1 slot for a Honing/Sharpening Steel.I designed the model into 4 printable parts so this could be printed on smaller printers like the Prusa Mini. But this also makes for easier cleaning since the bottom and...

The Version 1 is based on the original model, but with added material to compesate the extended face on the striker, and the second one is something I made because one of my magazines was giving me trouble, not really stoping when it needed. See what...

 I have it installed on both my printers and it's really nize.MK3S and (+) versions of the adapter are unique to each model and not interchangeable.Both adapters drop in over the screw heads as shown and get trapped between the extruder body and...

Update 2021/02/06: Upgraded parts- steering arm 2.0 Bump steer reduce for steering knuckle 2.0(the ackermann angle have been reduce on steering knuckle 2.0 and therefore with the change of geometry this part is required to reduce bump steer) Update...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

This is because it is a slide on design to limit the complexity of the model.  INSTRUCTIONS: I tried my best to make this the simplest adjustable optic for nerf yet! As such it has only 3 parts that can easily be printed in under 2...

# What you'll need This will work with any CH340 USB-serial chip I think, but the model here is for the CH340N for USBC. A picture of the exact chip is given. I ordered one from AliExpress for about $3, and one from eBay for about $6 (because it was...

The COMPLETE Order of the Labyrinth bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The strong Minocs of the Order of the Labyrinth are the descendants of Tesevros the Wise,...

Thank you very much and happy printing!Updates13/02/2022: Redisegned T-Slot-Clip so that the PTFE tube does not interfere with the cables on the side of the Raspberry Pi (see picture below).PrintingLayer height: 0.2 mm;Material: PETG (recommended),...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

The files are prefixed with Updated_ or New_.Here are a couple videos of it running  Please refer to the Original model for assembly and any other sources.I have uploaded the file as a Fusion 360 archive folder so you will need Fusion 360, Fusion 360...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

If your name is not Matt, then there is a template attached in the model files called “Name_Plate_Template”. If you wish to add your own name to this template, open the attached file called <code>Name_Plate_Template.step</code> in a CAD software of...

UPDATE 09.08.2022 •changed length for diffusor and mount from 10mm to 100mm •orientation changed for some models •added end cap UPDATE 12.08.2022 •added with diffusor / without diffusor comparison photo and electronics box wiring photo •added...

... this design, but don't want the silly text on the knife strip? Check out the modular version! Modular Wall-Mounted Magnetic Knife Strip

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

they are built into the models. Use the provided M2.5x10mm self tapping screws by default unless told otherwise. As an alternative to jig cutting, a drawing for manual hole drilling is also provided. In addition you will need: - Hot glue...

If you want to use the hardware I intended this to use: Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge) Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp&nbsp;How to create your clamp &amp; accessoriesSelect the clamp size...

If you need a shorter version then I have one of those too, see the shorter Z axis pointer thing.Print SettingsPrinter Brand:CrealityPrinter:&nbsp;Ender 3Supports:NoResolution:&nbsp;.2Infill:20%Filament:Amz PETG/PLAWhite&nbsp;Notes:&nbsp;Printing the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 74 printer_tolerance = 0.4...

We also offer other variations of this light if needed to fit your specific application, 120-277V AC, 12-24V DC, and 0-10V dimmable models.Our EPL-24-2L-LED-480V LED light fixture is NRTL Listed for United States and Canada approved for use in paint...

A custom-made enclosure specifically designed for the Raspberry Pi computer assistant Assistant assistant A bespoke casing tailored to fit the Raspberry Pi device. assistant Created especially for the Raspberry Pi, this is a one-of-a-kind case. ...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...