minolta af to canon ef adapter 3d models

I customized AlexEnglish's EF adapter (available at http://www.thingiverse.com/thing:10829), transforming it into a body cap for EF and EF-S cameras. Enhanced dimensions ensure a snug fit. Printed on my FlashForge Creator with black ABS filament, the...

The Canon EF-S lens features a 'pinhole' design that allows for increased angle due to extra clearance at the back. ...To print, utilize a thin layer thickness, such as 0.15mm, and subsequently puncture a minute hole using a needle for optimal results.

A simple adapter from Canon EOS RF (eos RP in my case) to a Schneider Robot Xenon 40mm f/1.9 It has some issues that I fixed "in post" as I didn't want to waste time and filament to reprint (and so miss from the model as I didn't want to add them...

A simple adapter from Canon EOS RF (EOS RP in my case) to a Schneider Robot Xenon 40mm f/1.9The v2 fixes a lot of these issues:no sanding needed, it's now the proper focal distanceadded a mark for the dot and a twist lock, the body is wider tooThe...

It solves some issues I had with the design.Resolved issues:T2 thread length is only 5mm (original model was 7mm, which was to long for most camera's)Canon EOS fit is tighter so it fits better to canon lensesThe internal opening is larger, causing...

Whether you're a professional photographer or an enthusiast looking to upgrade your gear, this protective cap is an essential accessory for anyone who demands the best from their Canon EF lens. It's a simple yet effective way to safeguard your...

I created this adapter from Hank Dietz creations thanks to him for amazing adapters! It holds strong even with heavy lenses. Body side don't have lock mechanism it holds by friction but it holds good and not moves unintentionally. I will try to...

This is a unique blend of two adapter designs, drawing inspiration from the following sources: http://www.thingiverse.com/thing:1727361 http://www.thingiverse.com/thing:237376 While I'm credited with bringing these adapters together, their original...

To optimize its performance, simply attach your wide-angle lens (18-55) with a 58mm diameter to the adapter's second section. With this setup, you'll be able to capture exceptional macro images. ...It's essential to note that printing it with multiple...

This is a lens hood I designed for the Canon EF-85mm It works great and I use it for my own lens. It is also reversable and just stays on my lens all the time. It is a tight fit as the 85mm only has a single groove for lens hoods to snap into, as...

This is a female lens cap designed for Canon EF mount lenses. I've uploaded the Zortrax file, pre-configured with printing settings that should work on high-quality ABS printers. Print Settings: Printer: Zortrax M200 ...

This is a lens hood for the Canon EF-85mm Prime Lens. I designed this lens as I couldn't find anything suitable for the type of lens mount the 85mm has. With a simple continous groove all the way around as opposed to the standard flange design of...

I remixed this to fit inside the extendable ring of the eyepiece. it fits very snug, but you still have to hold the camera. ...good for quick happy snaps

I got the printed mount stuck on the camera, so designed and printed the removal tool. ... The adapter is super btw : https://www.thingiverse.com/thing:1758168

Extension tube set (20mm/40mm/60mm) for Canon EF mount. Extension tubes let you focus a lens closer than it would normally, doing this by moving the lens away from the camera's sensor plane with a fit between the body and the lens. ...The end result is...

Raspberry Pi Camera Adapter: A Customized Solution for Enhanced Capabilities In a bold move, I've modified the standard lens adapter to accommodate the Raspberry Pi's rear camera module, complete with its essential front connector. ...Although I haven't...

Thickened the walls of the C-mount also set a tripod nut hole under the mount, you can super glue 1/4-20 nut in. ... use Black PETG or ABS, 0.12mm layer high and 35% infill

I designed this adapter to work seamlessly with an old 250mm Zeiss Ikon Talon projector lens on my DSLR camera. While I'm unsure if other Zeiss Ikon lenses will fit, I can confirm that the 250mm Talon allows for focusing beyond infinity. DISCLAIMER:...

... part. *The fitting may be different due to the accuracy of different 3D printers so you may need to have some diy skill and tools. Hope you enjoy the design. ... *You may not use this adapter on the EVF type of cameras e.g M5/ M50 or XT1...etc.

I'm excited to share my latest creation, a 10mm extender for macro photography, compatible with EF mount lenses. ...When printed with PETG, this extender provides an incredibly tight fit, but I've found that printing with other plastics may require...

Lens opener tool / Objektivöffner Minolta 55mm (50mm AF) to unscrew the front part of the lens OpenSCAD source for customizing for your own lens long and short version. ...Short worked for me, but is not very comfortable

Lens cap modelled after an original Canon cap. ...With or without lanyard hole

... perfectly. Tested on the 15mm to 45mm lens that came with my Canon M100, it it a perfect fit and easy to print. No supports necessary, it just needs time and PLA filament or resin. ...I will try resin next, but I expect that PLA is more durable.

The human took two swift cuts through a 60mm tube, effectively bisecting it, before carefully excising 20mm from its central section to yield a sleek 40mm tube.

... scad file. I just removed the intermediate step. If that doesn't work (see https://www.thingiverse.com/groups/thingiverse/forums/general/topic:49056), you can always install openscad and change the first line of the scad file to whatever you want.

After a few measurements and a quick session of modeling in Blender, I was able to create a lens hood that fits perfectly. Tested on the 250mm telephoto STM lens. No supports necessary, it just needs time and PLA filament or resin. ...I will try...

I made some adjustments to the 20 mm extension tube by SkyRzn because it didn't fit well on my camera. The diameters are the same; I just modified the connection between the tube and the lens. ...I love the results that come out of it!

However, an SR to M adapter also allows the latest Sony E mount bodies to autofocus these manual lenses via the Techart Pro LM-EA7 adapter, which has a 700g weight drive limit, making it essential to keep the adapter as lightweight as possible (this...

With this adapter you can connect any 1.25 inch eyepiece / camera to a Sony / Minolta A-Mount lens. The adapter opens up the aperture completely for maximum light. The lens should have a tripod mount, as this adapter has none. Use a M2.5 screw or...