mining rig fram 3d models

IMPORTANT If your setup is different than mine you have to modify parameters and values to fit your needs. Use at your own risk! Firmware was successfully compiled and tested with Arduino 1.8.5. Before compiling, be sure you have modified the file...

Especially if your filament isunder your printer (like I have with mine). Another problem with existing designs: They're way too easy to knock off their mounts! When reaching around the back of 5 filament spools you're likely to elbow one right off...

Mine is 1M for example. 3. Solder one end of the positive wire to pins 2 and 3 on the female XLR plug. 4. Solder one end of the negative lead to pin 1 on the female XLR plug. 5. Reassemble the XLR connector and slide up onto the wire any...

Just refile it a bit with a cutter!Update 31/01/24I started the electronic part with some late.The main issue is my board (NodeMCU esp32 or esp8266 d1mini)Both have some high deep sleep current, almost 20mAh, so running it on battery is pretty...

Just refile it a bit with a cutter!Update 31/01/24I started the electronic part with some late.The main issue is my board (NodeMCU esp32 or esp8266 d1mini)Both have some high deep sleep current, almost 20mAh, so running it on battery is pretty...

Yours will likely be different than mine since I installed a mosfet for my heated bed. 15b.) There will be six (6) wires to be unplugged. Four (4) power wires (2xRed, 2xBlack) and two (2) thermistor wires (1xgrey, 1xwhite; these will have a two...

A pair of bladed wings, also known as the Mach Blades, balloon-like mines called the Mach Balloons and spikes called the Mach Picks are there to depict the car with as much attention to detail as possible. Don't hesitate, hurry up to start the...

the O-ring shape is impossible to find outside of Macmaster Carr, Casting RTV molds coming soon!)...

After installation on mine, I was rewarded by a revolving green pattern which only covered half of the ring. It defaults to 24 elements and the ring has 40 so you need to pop into the settings menu to change it. So you Need a Logic Level Shifter? And...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of an adjustable...

Notes: (Important stuff!) While mine is done, this is a horrible project if I'm honest. I'm posting this so others can use the hot swap system and steal ideas but it's not an easy build, the wiring channels are really, really tight. Also note that...

I printed mine using Amazon Basics Black PLA filament with 0.2 mm layer height, 0.4 mm bottom thickness, 0.6 mm top thickness, and 15% zig zag infill. The filament is dark enough that you can't see the infill pattern with those settings. ...

Make all the parts and glue them together as shown in the pictures."Heater vent_milling" is used for milling."Heater vent_laser cutting" is used for laser cutting and hand tool making.Bearing HousingPrint the "Filament holder side bearing...

(see picture, mine isn't re-adjusted on this pic) Few M4x25, M2.5x20 Nuts & Bolts, few M1 self taping screws and you will be ready to print PLA, ABS without headache Led illumination will be added soon. 23 May 2018 : Parts "gauche.stl & "droite.stl"...

 When I re-print mine, I'm planning to remove that gap, as I think the paddles could be more durable without that gap.  A rock or something has ripped a corner off of one of my paddles - maybe without the gap that wouldn't have happened, or...

I only added magnets to the middle sets on mine. Middle Hinge to Corner AssemblyInsert a magnet into one side of the middle hinge. Then press the second half of the hinge together so the magnet is completely encased. Then fit the assembled hinge...

 Both mine and the original (remixed to metric) are provided.Remixed the UTA and LTA to accept a “sleeve”.  This is useful if you want to print theese components in not-black but don't want to paint them.  The sleeves themselves are...

Included is an STL of a heart with a generic “Be Mine” instead of names. There are three styles available to choose for creating the name: * a hidden internal lithophane (hold it up to the light to see the name inside) * an engraving on the top...

*this could lead to worse prints if your frame isn't rigid enough, but causes no problems on mine* *helps: corner bulging* ### Filament start G-code tweaks Filament Settings -> Custom G-code -> Start G-code They are executed later, after the nozzle...

Also make sure that black wire is much longer than main pen body. Solder the AAA contact.note: I trimmed mine AAA contacts with scizors to fit round shape Glue AAA contact in place. And push the middle_spacer to the...

The second possible troublemaker is the space between letters; check that there are no holes, and adjust fill angle, or extrusion widths, or detect thin walls, etc., to fix any; don't rely much on bridging, as it will be too high to show in the first...

The model I had found was a pencil holder, not unlike mine, only his had selectors along the side that let the end user denote upcoming tests and homework, and his does not spin-- if it can’t spin, is it really even worth printing? Despite its lack...

:) I included the modified STLs I used to make mine, basically smaller versions of DIY-Machines version and more of them and I added separate diffusers instead of his multi-filament versions, so that they can be printed on my smaller single-color 3D...

... controlled enclosure. Don't waste your time on them if your machine is not up to it (mine isn't). Update 2020-01-22: Added a front panel for the other ANET LCD with the knob in case someone might have that one instead. Category: 3D Printers

Check to see if the bushings are binding or dragging (mine weren’t on my first prototype, but were on the next version, even though I did not change dimensions). This can be caused by surface imperfections in the bushing seats, dimensional issues...

See the [notes on scaling](#notes-on-scaling-and-working-with-blender) in this document for a discussion on issues related to this model’s intended size. The kit includes an alternate version featuring an Original Series era nacelle. ...

 I set mine to 300mm^3/s^2 and this got me the best settings.  Non X1/P1 printers may need other settings.. read the mouse-hover tooltip in OrcaSlicer for an idea of what to use for your printer.Toggling certain features make things ugly.  Do not use...

I run mine with a RecoreMGN9H rails: 3MGN9C carriages: 3NEMA17 motors: 4Traxxas 5347 spherical joints: 12carbon / aluminum rods: estimate 6x 390mm for a 350mm bed - identical lengths required (< 0.1mm difference in lengths recommended)E3D V6...

Apparently mine featured an USB interface, hence flashing WLED was straight forward. As GPIOs usually are limited to 20 mA I needed to PWM these pins (described above). As these are just prototypes I never got around redesigning the bottom plate. If...

However, for those that would like some more detailed instructions I’m going to write out the step-by-step of how I assembled mine. This is not the only way to do it, just the way I did it. Hopefully this helps!Assembly Guide:1. Grab the center...