miniature microphone stand 3d models

Powerful microphone stands are equipped with sturdy clips that securely hold both upper and lower components in place. ...The lower clip features a spacious compartment designed to accommodate the audio cable connecting your tablet, ensuring a stable...

This microphone stand wouldn’t stay in position because there was a part missing in the clamp. I 3D Printed a replacement part which fitted in place. A holding screw prevents it dropping out. ...Now it’s fixed.

This is my custom Microphone stand I designed as I bought a microphone that came without a boom or a stand. It should fit most standard shock mounts (refer to the second picture). ...Do print with a fairly high infill for strength, I managed to print...

This interface piece bridges the gap between the mic stand and the microphone suspension - a design seen in Rodé's setup. At one end, it features a 3/8-16 UNF thread that fits standard microphone stands perfectly. ...A M6x15mm bolt is used to tighten...

I lost the stock stand for my Blue Yeti USB microphone, so I designed this stand with a slot for the oval extrusion on the bottom of the microphone to fit into. There is a slot for the USB cable to fit into, but I did not design a similar slot for...

... thread that Mic clips demand, so I decided to share it with the community in case someone else needs one. The custom-built stand measures 130mm from base to mic clip and is more than robust enough to securely hold my heavy Rhode microphone.

## Backstory This stand was designed to replace the standard shockmount included with many Aliexpress BM-800 clones and similar microphones. The original mini tripod stand was too small in all dimensions, making it impractical to use. It was too...

This is a basic stand holder designed specifically for the TONOR Microphone. Material: This stand is crafted from simple PLA. Required Components: You will need an M5 screw and bolt to assemble this stand. ... Included Files: The necessary Gcode...

... to attach securely onto the small, slender segment of the mic stand's structure. ...It expertly adapts itself to work in harmony with tubes of 15mm diameter, a measurement commonly found on some microphone stands as either the upper or boom component.

So i ended up making this 3D model because i needed a microphone stand quickly. So here is my design, it use the 5/8-27 standard thread used on many microphones. Approx 15cm in height and 12cm base diameter. UPDATE: I added a 60 degrees angle...

Humans use a microphone stand with a parabolic reflector, positioning their voice at the focal point within the curve. By directing the parabola towards your mouth, you can comfortably place the stand anywhere from 1.5 to 3 feet away. ...This eliminates...

... it to the arm requires an M6 25 mm hex bolt with nut. The legs from the microphone have been removed since they're no longer necessary due to the stand's presence. ...This setup gives my Zoom conferences a retro-style feel that I've been aiming for.

This is the stand for our microphone that is used for AI applications, 2 pieces for the ease of printing and to increase robustness. ...The body piece can stand in place without any glue or you may still use a fast action glue to attach the body part to...

The Samson C01U microphone comes equipped with a simple stand that demands minimal setup. To get started, simply submerge the upper bracket in warm water and carefully bend it inward, allowing the detents to function as intended. ...With this...

This was a custom-designed stand for my Razer Seiren microphone, built to fit the unique adapter that attaches directly under the mic's body. The screws used on this stand match those provided with the Seiren itself, ensuring a seamless integration.

A microphone stand I made for my elgato wave 3 microphone. I wanted something shorter and out of the way. I used a .4 tip with standard quality on my CR6, but I bet a .6 tip would do fine. I made the inserts to the base a snug fit so it doesn't...

The base is slightly larger and perhaps better looking.Print SettingsPrinter Brand:UltimakerPrinter: Ultimaker OriginalRafts:NoSupports: NoPost-PrintingPrint the foot, screw the microphone stand adapter that hopefully came with your microphone on it,...

Check out this custom Microphone stand I came up with after buying a microphone that didn't come with a boom or stand. It should fit most standard shock mounts, so be sure to take a look at the second picture. To get the best results, print it with a...

Backstory This is a stand for the standard shockmount included with many Aliexpress BM-800 clones and other similar microphones. The included mini tripod stand was just too small in all dimensions. It was too short which meant that the microphone...

It's fairly basic, but is designed to minimise the space taken up on the desk and to reduce the overall height compared with the supplied stand so that the microphone does not obscure your monitor screen. The overall height, including the...

A sleek microphone stand that embodies minimalism. This iteration shares the exact same interface as its predecessor, a design available on Thingiverse with the reference number 1425977. ...Its base has been enlarged and polished to perfection, giving...

Simple stand for a SingStar mic that fits any conical microphone with a shaft diameter of at least 32mm at its thickest end. ...Designed in Fusion360 and scaled down by a factor of 1000, although I didn't bother fixing the error.

A compact desktop microphone stand that features a detachable adapter for effortless mic removal. ... *** Those interested in editing or creating their own adapters can access the Onshape link:...

This clever adapter lets photographers repurpose a mic stand as a trusty camera boom. ...A part of its design mimics that of a standard microphone, while the top boasts a versatile 1/4-20 screw for effortless attachment to a camera's bottom.

ADesktop Microphone Stand with a detachable adapter to remove the mic easily. Onshape Link if you'd like to edit or make your own adapter:...

Created this to support a small trophy case on top of a microphone stand. ...It is a generic adaptor; the ANSI 5/8-27 threads used in US market audio equipment on one end, non-tapped holes on the base to screw or bolt it to stuff.

The original FIFINE K669B stand takes up too much room on my desk. This one has a smaller foot print. The model is completely hollow. Keep the metal ring on the bottom microphone screwed in. ... Filament amount: 26g Colors used: <a...

Adjustable phone holder for microphone stands When you cant remember your lyrics when playing guitar, clip this in front of your face and just read the lyrics over the microphone while still playing guitar. You will need an elastic to make it...

Customizable for any microphone by adjusting the top and bottom diameters to match the taper of your microphone at a precise 4mm separation. Mine is a Shure 10A with an outer diameter of 37mm at the top of the mic. This utilizes the "arc" module in...

This is the oft-faulty small plastic component of a microphone stand securing mechanism to link the stand components together. In case you're experiencing this issue, here's the solution. I printed it in PLA with 0.2 layer height, 0.4 nozzle size,...