miniServoMount for tower pro sg 50 servos's 3d models

Build anything and everything you imagine by snapping micro 9g servos right into this totally Lego-compatible brick - and rock your next creative project to new heights instantly!

This is an enclosure for the 20W PA module from SG-LABS. ... Drill template is inclusive.

Since the servo I used is oversized compare to normal ones and I don't have arduino nano in hand, I decided to design my own OTTO parts based from 101Robotics' design(https://www.thingiverse.com/thing:3664685)

This fan duct is for a limited edition of 50 pieces of Flsun QQ-S Pro. One of the differences is the hot end block, on which, instead of the second cooling fan, a magnet is installed that holds the table calibration sensor. The remaining fan cools...

This is a remix of the Caterpillar Robot ID 228426.\nThis robot uses standard servos and has excellent ground clearance due to the positioning of the servos.\nThe wheel design was modified to prevent caterpillars from appearing, Use 1.75 filament to...

A miniature plastic micro servo is suitable for lightweight applications, offering precise dimensions for optimal performance.

The Tower Pro MG90S also features a wide range of operating speeds, allowing users to fine-tune their control over the servo's motion. ...Whether you're building a robot, a model airplane, or any other project that requires precise control, the Tower...

Hello, I make this vent cover for CR10 S PRO because I see some dust come into the fan. ... for that I make this cover with filter to prevent that and bonus this make some noiseless for the fan.

Hello, I make this vent cover for CR10 S PRO because I see some dust come into the fan. ... for that I make this cover with filter to prevent that and bonus this make some noiseless for the fan.

This is a simple to print (use supports and print upside down) and mount addon for your Pro's kit SS-331. Just use a bit of double sided tape to attach it to the top of the station. Finally, you have a place to safely store the extra nozzles, the...

This is a simple to print (use supports and print upside down) and mount addon for your Pro's kit SS-331. Just use a bit of double sided tape to attach it to the top of the station. Finally, you have a place to safely store the extra nozzles, the...

made a cutout, because on my QQ-S pro the extruder gear collides with the original design

...Check it out at robotshop.com/ca/en/futaba-spline-metal-servo-horn.html --- A draft CAD model of the FMSH-01 Servo Horn, compatible with TowerPro MG-995 motors, is ready for viewing. It does not incorporate gear extensions or threaded hole features.

A remix of the Spool Holder for FLSUN SR Super Racer by OoeyDuck resized to fit the spool holder for the QQ-S Pro as the SR holder is about 5.6mm longer. ...Just print it the same as the original.

Made this cause the Stock steering-Arms where not good enought for me. The one with ball-connections was straigt and i could only steer on like 35-40 % safely. The other one has a steering angle of up to 75 % BUT has no ball-connections. So it...

This is a body cover for the Mamiya RB67 Pro or Pro-S. It covers the rear of the camera body when the film back is removed. The body cover is marked for easy identification. May also fit the Mamiya Pro-SD body, but this has not been tested. I...

I create this custom vent cover for my CR10 S PRO printer because I noticed excessive dust entering the fan and causing problems.\r\n\r\nTo address this issue, I design a custom cover with a built-in filter that effectively prevents dust from...

This is a low bugget enclosure for QQ-S PRO. You have to use a styrofoam board with 14mm thickness for best results. You can also choose between 30 ou 40mm foot, remembering that you have to use 6 of this. ... *** DO NOT FORGET To cut the styrofoam for...

This is a low bugget enclosure for QQ-S PRO. You have to use a styrofoam board with 14mm thickness for best results. You can also choose between 30 ou 40mm foot, remembering that you have to use 6 of this. ... *** DO NOT FORGET To cut the styrofoam for...

Here is a high-performance servo motor designed specifically for robotics and automation applications, available in both Sldprt and Stl file formats.

With its high torque output and fast response time, it's perfect for applications requiring delicate control, such as robotics, model airplanes, and remote-controlled vehicles. This affordable and reliable motor boasts a wide operating range from 0...

This is a simple work volume for the 360 degrees Tower Pro servo. Please note that the teeth for the brass gear might not be exact. ...It might require some playing around to work right

9g Micro Servo that is commonly used. ...(Note: Screw and Servo connector missing)

G-Code with temp change for PLA & PETG & TPU

Inspired by [this](https://www.thingiverse.com/thing:3603640) design by [Maffo_3d](https://www.thingiverse.com/maffo_3d/) I modeled up a design with better ergonomics that also snaps into place securely on the new S/Pro models.

make sure to increase the size of the servo horn, what worked for me was 110% also rotate it 90 degrees on the x axis to make it sit on the bed (red line in Cura)

Angled ribbon holder for CR10S PRO, designed with Fusion360. This holder keep the ribbon above the printer stand. Needs just to tapping the hole of interface_a for lock interface_b with en fastener, but other solutions are possible ! ...The ribbon...

... ...It appears to be a deliberate design choice rather than an oversight. Upon further inspection, I'd like to propose exploring alternative shaft connector designs that could potentially eliminate the need for these two different head sizes altogether.

A popular robotic servo dummy is a highly useful tool in designing and projecting Trackers, as well as various types of robots. It provides users with the ability to test and refine their projects before moving forward. In addition, a design spark...

This is a body cap for the Mamiya RB67 Pro-S. It fits on the front of the camera when the lens is removed preventing dust and debris from entering the mechanism. It is marked with the camera model for identification. Unlike the Mamiya RB67...