mini z rc 3d models

CR-10 Mini Z-Axis Brace Brackets, Designed for Maximum Versatility These brackets will probably fit other CR-10/Ender series printers with some threaded rod length adjustments. The upper bracket is long enough to clear the print head assembly and a...

... of the printer. ...This mod of the z bottom has the end stop to the y base moved by 3mm, resulting in the whole z assembly being moved 3mm further to the rear end of the printer. ...Print instructionsPrint as instructed for the Original Prusa parts

... by the 2 screws holding the rear bumper. I had the little ball socket screw thingie from the suspension linkage on an old RC car. Enjoy! ...Also check out my roof rack for the Jimny here: https://cults3d.com/en/3d-model/game/1-24-scale-roof-rack

This is a wheel that fits Wltoys K989, K969 and other similar 1/28 scale RC cars. All parts push together but a small amount of adhesive may be needed depending on your printer calibration. These wheels are based on the popular SSR SP1 wheel. The...

... the rear bumper. I had the little ball socket screw thingie from the suspension linkage on an old RC car. Enjoy! ...Also check out my roof rack for the Jimny here: https://cults3d.com/en/3d-model/game/1-24-scale-roof-rack Category: R/C Vehicles

Simple cap to place on the Z axis motor to prevent dust from entering the motor. ...Designed with cutouts to allow the cables at back of motor to exit.

just a spool rack. ...fits comfortably over z motor, reasonably stable. you can tighten it down with tape or, or paper dowels. ...I would leave it loose for cooling though.

This is the Z-Axis spacer that I use on my printer. It is 5mm tall. I needed the extra height on my printer. ... It's not glamorous but it works.

... ...The design has thus been adjusted to suit 0.2 inch belts. For those with OpenSCAD, this modification is straightforward; an .stl file is also provided for convenience. Simply replace the z-driven-pulley and two z-driven-rims with the updated parts.

This is a REMIX of the Z-axis brace by Fada, where it is enhanced by removing the very sharp mounting hole and moving one of the beams out further in an attempt to stuffen the Z-axis more in one direction and adding another beam in the other...

I was quite surprised how this was over looked, but its a super easy fix :D No need to dismantle the Z top end or the Extruder assembly.This little adaptor fits comfortably between the extruder and z axis  mounts. The issue is that the...

I modified a design made for an Ender 3 to work with a Prusa Mini. Original link: https://www.thingiverse.com/thing:4054237 Super glue a 8mm X 3mm rare earth magnet to the bottom. ...Print instructions40% Infill Use supports

This is the Z-Axis spacer that I use on my printer. It is 5mm tall. ...I needed the extra height on my printer.It's not glamorous but it works.If you would like to support me: https://ko-fi.com/tinyboatproductions

Broken Part for My Up Mini 2 Created Using SolidWorks 2016 Software and Printed on the Same Machine with 0.8 Kg of High-Quality ABS Plastic Material, Finished in Just 25 Minutes with an Extremely Fine Layer Height of Only 0.2 Mm.

I modified a design made for an Ender 3 to work with a Prusa Mini. ...Original link: <a href="https://www.thingiverse.com/thing:4054237">https://www.thingiverse.com/thing:4054237</a></p> <p>Super glue a 8mm X 3mm rare earth magnet to the bottom.</p>...

print this if you have printed my squashball feet and want to have z support brace together with a foot right under it. 2 parts printed separatly to make it an easy print, pieces just slide right into eatchother (glue it if you want to). Link to...

Have the best co-pilot watch over your prints with this BB-8 z-axis visualizer! ...It comes with a docking station that goes on top of the motor to house BB-8 and protect your motor from dust and the elements.The shaft connects with the motor with a...

The alignment of the holes in the original print was not compatible with my printers, so I adjusted the hole spacing to accommodate my z-axis rods perfectly.\r\n\r\nSpacing: 17mm on single rod, 18.5mm on double rod\r\n\r\nI found this solution by...

Silences the Z-axis linear rails from vibrating and producing excessive noise. Print two of each and position them at the top and bottom of the rails under the metal bracket. Previous versions failed to meet my requirements, but I designed these...

The Human Coupler efficiently transmits motion up and down the rod without inducing unwanted Z-axis wobble in prints. It achieves this by allowing the top and bottom of the rod to move freely, preventing movement transfer. A distinctive cup-like...

... disassembly and extra arms sticking out. This SCAD requires the Triangles module found here: http://www.thingiverse.com/thing:220868/ Print Settings Printer: Monoprice Select Mini Rafts: Yes Supports: Doesn't Matter Resolution: 0.2 Infill: 85%+

... nuove catene ecc.... ...pubblicheroò il materiale un poò alla volta appena riescoclip cavi: https://www.printables.com/it/model/554572-clip-cavi-per-profilo-30x30Zampe: https://www.printables.com/it/model/567955-fysect-mini-zampe-o-piediniCategory: DIY

I didn't like the small gaps over the Y extrusion, and realized I could fill all of them with colorful hexagons fit perfectly to the design.&nbsp;This was designed in TinkerCAD, with the main Z brace acting as a hole to cut the exact hex...

So I've been getting back into using my Chinese-made Harbor Freight Mini-Lathe and wanted to add a DRO but didn't want to spend big bucks. Instead, I designed one of my own using an economical dial indicator that I got off Amazon and extended the...

This bearing clamp has been thoroughly tested and verified to work seamlessly with: MP Select Mini X Gantry Support + Camera Mount [Reinforced and Realigned], a project designed by svideo and available on Thingiverse...

A Phalanx CIWS to protect your printer from whatever dares to harm it!The Phalanx sits on the top of the Z-axis motor no magnets needed!Included are three parts the gun, base, and fastener. To assemble, put the rod through the base and gun, depending...

I decided to create a new Z axis based on the Y and X axis design to lift the pen out of the way rather than rotating it. I found rotating the pen left little strike marks on the paper. I also added a different pen holder. The pen holder design uses...

To fix this issue, simply slide one of the adapters onto the z-axis sled and it will trigger the end switch sooner. This solution seems a lot less expensive, more reversible, and faster than installing an adjustable switch holder... One of these...

I'm converting the CNC conversion for my Little Machine Shop mini mill (3990). I got the bulk of the design from LittleCareBear's creation, but I wanted to make some changes. Parts required: M5x0.80 20mm bolt (7) M4x0.7 20mm bolt (4) M4x0.7 nut...

So I have been getting back into using my Chinese made Harbor Freight Mini-Lathe (see more here: http://diy3dtech.com/mini-lathes/) and wanted to add a DRO (Digital Read Out) to it but didn't want to spend big bucks so designed up one of my own using...