mini table saw 3d models

This part serves as a protective end cap for the aluminum extrusion Vega Table Saw Fence. As received, the fence arrives capped with pieces of sheet metal that not only appear unsightly but also fail to conceal the sharp edges that can inevitably...

This knob fits the common 10in table saw "white labeled" to Craftsman, Tradesman etc starting in the early 2000's. The arrival knife in the back is removed with a 10mm wrench. This print makes the arrival knife much quicker to uninstall without...

This replacement handle grip is specifically designed for the Biesemeyer fence that accompanies the Delta model 36-725, a high-end 10-inch Contractor Table saw. The metal pin that this grip fits snugly over boasts an M6-1.0 thread in its base. ...A...

On an Evolution Rage 5S table saw the dust extraction is in 2 parts, one from underneath the blade and one for the blade guard. If you are not using the blade guard, then you are left with part of the extraction pipe sucking nothing useful and needs...

Purchased a pre-owned Ryobi table saw but discovered that the miter gauge cover was missing. The original factory-supplied cap had a flat design, which didn't fit comfortably in my hand. I sought out an alternative that would provide a more secure...

Fingers guard design precision table saw Proxoon. Essential two M4 screws and one nut. Materials needed include PET for protection and PLA for hooking. Once constructed, it attaches to the side guide, allowing smooth sliding into place. Print...

Neighbor needed a throat plate notched wide enough for a dado blade on his Makita table saw. I designed this for him and printed it and it works great. I've made a split version with a recess and insert so you can print it on a smaller printer and...

I have a table saw in my classroom shop, equipped with a dust collector bag attached underneath it. Cleaning out the accumulated debris can be quite laborious. The attachment's design aims to prevent the frequent clogging that typically occurs when...

Dust collection adapter fits perfectly between the Dewalt 7480 Table Saw and a 2 1/2" dust port. Compatible with all 2 1/2" ports, it's a must-have for any serious woodworker. I personally use mine with my Ridgid 4 gal. shop vac, but it should work...

... of sliding off the legs if you repeatedly move your table saw around the workshop, like I do. I previously posted a replacement dust collector joint (PC part number 5140085-31) for the same table saw at https://www.thingiverse.com/thing:3399580

For example, if you want to make an 8 sided object, you would use this guide to set the angle on your table saw miter gauge so that the angles are set for 8 sides.With the numbers facing up, place the miter bar in the guide for the desired number of...

Designed for: 1/4" x 20 Hex Nut or Bolt 3/4" Miter Slot with wider bottom groove Dimensions of Miter Slot on my Table Saw (Rigid TS3650): Overall Height: .42" Upper Slot width: .759" Lower Slot Width: .95" Lower Slot Height: .157" Top of T-Nut sits...

Let's face it, the miter slots on the Ryobi Table saw are bad, other than that, great saw for the price. This is a group of files that that help improve the miter track. First off is the miter rails, there is one with the arrow and holes already laid...

I put the magnetic strip on the back of the table saw where it is out of the way. I ran the magnetic pickup sensor inside the fence so it some out the back and is mounted to the underside of the fence. You could also run the wire on top of the...

I liked the emergency stop paddles I saw on other table saws, and I wanted one!I have made one with two parts.This has an attachment fitting, in which the inner surface is shaped to match precisely the piece that it is mating to. It can be attached...

The nut from the original post was too big for my saw so I redesigned one based on the dimensions of the miter slot on my saw.After that I decided that the featherboard itself was a bit short so I lenghtened it by 5mm. I also increased the diameter...

I have an affordable Delta bench-top table saw that utilizes a non-standard T-profile miter slot. I'm looking to create some jigs that make the most of the slot, but I couldn't find a part that caught my eye. The OpenScad design file is available...

Bill of materials: - 4 x corners ,3Dprinted, 44mm-height (Table-SAW_-_Housing-support.stl) - supports 3Dprinted(support_table_saw.stl) - 2 pcs - bearings MR105(5x10x4mm) - 4 pcs(2 on each support) - threaded inserts M3(hot inserts on corners, table...

spare part for band saw Metabo BAS 380.

The Flex Shaft is available here: https://www.amazon.com/Dremel-225-01-Flex-Shaft-Attachment/dp/B0000302Y8/ The table saw is inspired by https://www.thingiverse.com/thing:670704, but with some modifications. For assembly you will need the following...

Designed for: 1/4" x 20 Hex Nut or Bolt 3/4" Miter Slot with wider bottom groove Dimensions of Miter Slot on My Table Saw (Rigid TS3650): Overall Height: .42" Upper Slot Width: .759" Lower Slot Width: .95" Lower Slot Height: .157" The top of the...

Drill Press (on left side) Circular Saw / Router (on right side) Work Table (in center) All tools feature: Rear X-adjustment via rear main horizontal rods, Z-vertical rear rod adjustment, X/Y positioning arms. The tools are easily removable and can...

... Hi Guys, i designed a bracket for my Evolution Table Saw. The Bracket is designed for the groove for 20.2 mm. take a file and grind it to your wanted size..thats the way i did it.. Also Needed: M5x16mm Screw and Brass Knurl Nut M5. ...

I am thrilled to introduce my latest creation, the table saw fence micro adjustment slider! This slider is specifically designed to perfectly fit the Biesemeyer Fence System, which uses an aluminum extrusion rail. To ensure a perfect fit, simply...

I've been living with a broken table saw for far too long, its cheap handle having given out on me ages ago. It's finally time to take it apart and rebuild it from scratch, making the most of this opportunity to make some much-needed improvements...

Needed rails for a cross cut sled that fits my SawStop table saw can be custom-made with standard measurements in mind. To facilitate this process, I've attached the Fusion file so users can easily edit and tailor it to their specific needs. I...

Our Westfalia MJ10250 table saw was missing a footcap, so I measured one of the remaining caps and designed a similar one, which fits well. Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: No Supports: No Resolution: 0.3mm layer height...

... Additional information about this project can be found on my blog at https://makeverse.home.blog and specifically at https://makeverse.home.blog/2019/03/02/featherboard-for-bosch-pts10-table-saw/. ... I hope you find it enjoyable.

Dremel table saw with cutting angle adjustment I was needing to make cuts at 45 degrees with my microrectifier, so I found this project https://www.thingiverse.com/thing:2365532 and from it I created my modifications. It is preferably necessary to...

I created this to fit my Ridgid shop vac (with the standard 1.57 inch/40mm hose) to my DeWalt 7491RS table saw (with the standard 2.5 inch/64.5mm dust collection port). There are many other dust port adapters out there but I couldn't find one that...