mini snap on toolbox 3d models

... it at https://www.thingiverse.com/thing:1692395. This model works perfectly, but I noticed that the part doesn't look great on my printer due to the overhanging features. ...To fix this issue, I've created a modified version with reduced overhangs.

The gimball protector designed by Tekniqueman suits perfectly, but I don't use the neck strap and found that the protector wasn't secured in its proper position.\r\n\r\nTo fix this issue, I simply attached a clip that holds it firmly at the ring...

Thanks to idig3d for the original design.https://www.thingiverse.com/thing:1692395Works perfekt, but the part look not so nice with my printers because of the overhangs.So here the part with less overhangs.LicenseSnap-on Filament Filter/Oiler (less...

I adapted Dakanzla's 2.0 pieces to fit seamlessly on the 1.0 version. His design captivated me so thoroughly that I had to remix, adapt and utilize it. ... The following ports have been remixed: 3-1 part Sheep Port Wood Port Wool Port Brick Port Wheat...

i remixed Dakanzla's 2.0 pieces to fit on the 1.0 version. i was so in love with his design so that i had to remix, adapt and use it. ... following ports are remixed 3-1 part sheep port wood port wool port brick port wheat port

... ...Secures the pins on the back to prevent electrical shorts without needing to snip them off. Uses hot glue to anchor the mount exactly where it's needed. Printed in durable PLA material, layered at a precise 0.2 height, and features a sturdy brim.

I aimed to see if I could attach a decorative lens on top of the iris holder. I call it decorative because it's extremely challenging to produce a completely transparent 3D print. Examining them is similar to wearing Vaseline-coated glasses. ...If...

Allows you to attach your raspberry pi to the side of the Prusa XL. ... I used this case but really any case that uses the pi mounting holes should work:  https://amzn.to/3QhL8hbI was able to use the screws included with the case.Tested on a Pi 4B

Sits very tight. ...Covers the pins on the back to prevent shorts, don't need to cut pins. Hot glue the mount where you want it. Printed in PLA, 0.2 layer height, brim. ... https://www.youtube.com/watch?v=362oagqQhyw&feature=youtu.be

This is a very basic M-LOK Cover plate that should fit into the holes.Flat side on preferably textured plate for a nice texture.IMPORTANTYou may need to change the dimensions in your slicer to make it fit as snugly as possible, in my case I had to...

I have been relying on adhesive-backed LED strips to illuminate my print bed on my Makerfarm Prusa i3v 8" printer, but the adhesive eventually gave way and the strips ended up stuck in my print. Determined to find a solution, I set out to design a...

I created this saddle for my vacuum system, I use this to connect a hose that on the other side is connected to one of my machines. The saddle fits on a 60mm pvc pipe and in the other side fits a regular vacuum hose. (40mm). Drill a hole of 50mm in...

I'm working on getting the cooling fan turned off during purging so the filament doesn't want to curl and jump the ramp. ...You can see this happening in the video.</p><p>YouTube video:</p><figure class="media"><oembed...

Thus, I revamped the wheel design, making them larger and rounder (120 steps compared to the original 30ish) to enhance rolling performance on plastic axles. Additionally, I added dualstrusion rims for a multicolor, fancy appearance. To achieve...

Infill at a rate of 25-40%, depending on nozzle size and the specific flex material used. This combination provides strength while allowing for sufficient flexibility to absorb vibrations. Alternatively, print feet with solid materials and add a...

... sleeve. Protects the screen, fader and knobs.Prints very easily with no supports required.There are small cutouts in the 4 corners of the inside of the case for some 1mm thick rubber tape to prevent the case from rubbing on the beautiful KO II.

I've recently acquired an sjcam m20 for which I built this modification\r\n\r\nIMPORTANT: please note that my camera features a lens barrel with a diameter of 21.6mm, the inner diameter of its cap is 22mm, and its depth is 4mm - the lens doesn't...

... bearings over time. ...Consequently, I designed my own custom LM8UU holders. The press-fit ensures that the LM8UU remains firmly in place within the components and will never come loose again.\nPre-assembled for immediate installation on any Prusa i3.

This is a series of Jack-o-lantern faceplates designed to fit the original design by thjelmfelt https://www.thingiverse.com/thing:2590046 All of the designs were stencils I found on goggle and used Inkscape and Solidworks to create. I did not...

... unfortunately. How it works: https://youtu.be/4G6hYgOzZvI Also includes parts for the Switch Joycon version. The linkage dimensions depend on which side Joycon you use and how far up you mount it, you might need to shorten the linkage bar.

... attach it directly to the pipe using durable cable ties or robust elastic rope for added stability. This DIY phone holder was crafted by replicating the shape of my phone case, allowing for seamless integration and effortless mounting on my bicycle.

I recommend printing the lid plate twice and gluing it to the top and bottom surface in the middle of the lid for added stability.I've printed this lid four times, and it fit perfectly on all four baskets (one basket was purchased almost 1 year ago,...

... a strong glue to attach the magnets to the two halves, I recommend a thick super glue. Make sure the magnets are placed so that they are ATTRACTED to the magnets on the other half! Enjoy! ...And if you make any cool remixes please let me know!

I sliced the STLs with the variable layer hight option to make sure the dimensions in certain areas are getting printed correctly.STEP file is attached if you need to tweak something…Hygrometer can be found on Amazon - I ordered this one (no...

I didn't have any calipers on hand to take precise measurements, so I hope it fits together smoothly. I'll test print again and make adjustments as needed. Since I'm printing in PLA, if someone could print in ABS and let me know how well it fits,...

With an infill rate ranging from 25-40% depending on nozzle size and type of flex material used, these feet proved strong yet flexible enough to absorb vibrations effectively. Printing out solid materials is also possible, and using a layer or two...

... model. Use the original cam and screw from Andrew Godfrey's original design. A Remix of Andrew Godfrey's Soldering Clamp found on Thingiverse - I just made the base wider for more stability and added 4mm to the bottom to raise it slightly.

It fits quite loosely on mine so pretty easy to pull off but stays stuck if you throw the camera around like a crazy person. Maybe play a round with the scaling if you want a better fit. UPDATE: Made it a little better. The previous version was...

... mount, you will only need the necessary hardware required by the mount systems. Important Note: When mounting any item on the left side of the hot end (such as an OEM sensor), ensure clearance before homing to avoid potential conflicts or damage.

It works as a stand-alone holder but to keep it clipped to the keyboard in tight situations like economy class airplane seats, you need to print two of these to keep the keyboard stable and protect it from turning on in your bag:...