mini skyhunter 3d models

The Mini SkyHunter V2 is a highly advanced drone designed to capture breathtaking aerial footage and stunning photos from above. With its lightweight yet incredibly durable construction, this compact powerhouse can navigate even the most challenging...

Various parts for a SonicModell mini Skyhunter. ... Battery tray Motor mount TBS Crossfire Nano SE mount Matek VTX mini mount Generic FPV camera mount x2 wire tidy's All designed to be printed in PLA.

Various parts I utilized for my Mini Skyhunter VTOL conversion. Flight Controller and Battery trays were inspired from grahame addicott designs. The boom mounts are for the stock boom tubes and some additional 10mm tubes. ...

I redesigned the Mini Skyhunter tail mounts, because the original ones are sooo heavy (20g each), this version is just 12g each (PETG, depending on print settings) This part might also fit for the big Skyhunter (1800mm), but I'm not sure (let me...

A pan tilt mechanism for a SonicModell mini Skyhunter. ...The mechanism is designed to house a Runcam Split 3 micro and x2 TowerPro MG90S servos.

The mini skyhunter cockpit boasts an impressive 1238mm wingspan, far from a diminutive design. ...This ingenious camera mount is tailored for use with a versatile tool, available at https://www.thingiverse.com/thing:1110726, which seamlessly integrates...

A flight controller mount for a mini Skyhunter. This mount is specificially designed to house a Matek F722 flight controller, as well as a Matek SAM-M8Q GPS unit and a LittleBee Spring 40a ESC. Similar sized flight controllers, GPS units and ESC's...

I recently found a nice Y3 VTOL Conversion for my Skyhunter, wich i tried. I noticed, however, that most of his parts are very secific for his chosen parts and you can´t convert an existing model. So here you have basically the same Kit, redesigned...

Some cooling covers for the mini skyhunter wing pockets.

Remix of https://www.thingiverse.com/thing:4011721 scaled for the Mini Skyhunter, and trimmed to reduce weight.

You can find all the information in this article on my website: http://www.sop-fpv.com/tecnologia/item/28-mini-skyhunter-vtol-y3-parte-i, and http://www.sop-fpv.com/tecnologia/item/29-mini-skyhunter-vtol-y3-parte-ii. Edit: I have replaced the...

... flat, so a slight tilt will be necessary when mounting a camera. My hope is that this remix will serve as a valuable enhancement for your mini skyhunter project. With 3 perimeters and 20% infill, this model weighs approximately 16 grams. ...Cheers!

I'm excited to share my first contribution with this community. I've been working on a project that's still in its early stages, but I thought it might be helpful to others, so I'm sharing my progress. As part of the design, I had to experiment with...

I got fed up trying to repair the foam control surfaces on my Mini Skyhunter. So I decided to create these - they're simple but effective and work perfectly with the control horns that come with the package. ... The plywood plates with blind nuts failed...

This model was created with Tinkercad. ...Make adjustments online at https://www.tinkercad.com/things/k4g3V5Kz1F7

This model was crafted using Tinkercad. ...Modify it on their website at https://www.tinkercad.com/things/8Z4r2MgGfPq

Humans are still evolving and need to make significant advancements to reach their full potential.

This creation was crafted using Tinkercad's powerful tools. ...Edit it directly online at https://www.tinkercad.com/things/dPIiLADxUlR to unleash your creativity.

This is a mount designed specifically for the ReadyMadeRC Mini Skyhunter, also known as the Eachine Micro Skyhunter, Sonicmodel Mini Skyhunter, etc. This version is tailored for the mid-sized model, not the full-fledged Skyhunter or the...

!!! ADDITIONAL HARDWARE REQUIRED !!! These have been designed to take a standard M4 nut. Therefore you will need to buy M4 screws of the correct length for this to work for you. You will also need to drill out the white washers on the wings to...

I am engineered to function optimally when paired with high-strength carbon fiber square tubes measuring 10 by 10 millimeters.

The shelf location is too high up in the fuselage for modern flight controllers which have servo plugs in the vertical orientation. Servo plugs will foul against the wing roots when attached. I designed this part to lower the shelf by 10mm in...

Here is the rewritten text: Simply insert the 36x36mm flight controller into the designated rear wooden compartment of the Skyhunter, where it will seamlessly integrate with the system.

Lightweight and small support for making vertical stabilizers more rigid. Print and glue in place. ... Parts weight less than 5g (2.4g each) so it won't add any real weight to the tail wing.

The original rudder feels too mushy. Replacing it with stiffer components will make all the difference. ... I'd rather have it printed with PETG for enhanced heat and sunlight resistance.

It has been lengthened by 2mm and new mounting holes (32.5mm x 32.5mm center to center) have been created to allow mounting a APM mini GPS that uses the same mounting hole pattern. I printed mine with 4 bottom and 4 top solid layers, 0.100 layer...

Instructions: 1) Install standoffs in the new holes on the mount 2) Attach your flight controller or GPS to the standoffs 3) Remove the existing wood tray from the Nano Skyhunter 4) Place the mount at a slight angle and press it into the foam slots...

Skyhunter AA Vehicle.

I constructed the Skyhunter prototype using Photomodeler software. ...The interior of Skyhunter adheres to metric standards, while the exterior does not follow this measurement system.

Skyhunter Drone The UAV (Unmanned Aerial Vehicle) Skyhunter is a cutting-edge technology designed for various applications, including surveillance, reconnaissance, and targeted attacks. This high-performance drone boasts advanced features such as...