mingda d2 3d models

Download BLTouch firmware from: https://www.3dmingda.com/download/firmware.html (Ex: D2 Firmware for add BL Touch) 2. Format SD card for FAT32 3. Add Mingda download "Firmware.bin" to formated SD card 4. Turn off power to printer, unplug power. ...

There where no Mounts for the Mingda D2 that fits my needs. So i decided to design my own one and this is, what i came up with. It can carry the original Fans. So you dont have to get new ones! :-) This is free of charge, but use is at your own...

https://youtu.be/Z0F9gUV0d3M Mingda D2, BMG directo, E3D v6, Antlabs BlTouch, LED Blanco, he modificado la parte trasera por donde pasa el cableado, en el lado derecho mirando de frente choca con el tornillo de la rueda de perfil, ya he modificado la...

https://youtu.be/Z0F9gUV0d3M Mingda D2, BMG directo, E3D v6, Antlabs BlTouch, LED Blanco, he modificado la parte trasera por donde pasa el cableado, en el lado derecho mirando de frente choca con el tornillo de la rueda de perfil, ya he modificado la...

This is a side mount for Raspberry pi. Also look for the companion things of the Arms and Camera things. https://www.thingiverse.com/thing:4660355 and https://www.thingiverse.com/thing:4660358 These were remixed from the following things.. I took...

The printer bed cable rubbed against the frame and was consumed or often went under during movement. so I made a simple structure to support it. It works and I find it useful. I hope it will serve you. So little time! I hope you guys enjoy...

So I noticed on a tall print that the filament sensor could get in the way and also the angle of the filament was at a hard angle so i made one that could pivot a little and see if it makes a difference.. its a simple design and the 2 holes for the...

Get better cooling and better air flow with this fan duct

Made a few adjustments from the original design to make it a little taller than the original and one side was slimmer as the original wasn't allowing the wheel on the tensioner to move freely. The slimmer side should be up against the tensioner...

condotto aria per raffreddare il pezzo l' aria arriva direttamente e in modo concentrato sul nozzle venite a trovarci sul gruppo facebook italiano https://www.facebook.com/groups/mingdaitalia/ ...

This is a side mount for Raspberry pi. Also look for the companion things of the Arms and Camera things. https://www.thingiverse.com/thing:4660355 and https://www.thingiverse.com/thing:4660358 These were remixed from the following things.. I took...

material PETG infill 60% resolution 0.2 support yes

This is a BLTouch mount that takes less than 5 minutes to install. You simply take the two top screws out and use 2 M3 Socket Head cap screws about 10MM long. You can mount the BLTouch with same screws. ... The offset in Marlin is X=8 and Y=-44 ...

For the profiles of the MINGDA D3/Pro, D4/Pro and Rock3/Pro look here: https://cults3d.com/en/3d-model/tool/mingda-cura-4-8-profiles-for-rock3-pro-d2-d3-pro-d4-pro !!!!!IMPORTANT!!!!! ~THE FOLLOWING WILL UNINSTALL ALL YOUR CURRENT SETTINGS! YOU MUST...

Usually found under C:Drive>Program files>Ultimaker Cura 4.8> /resources/definitions /resources/extruder /resources/meshes /resources/quality /resources/variants After you're done 1) Launch Cura 2) Select "add a non-networked printer" 3) Scroll down,...

material only PETG ABS ASA infill 60% support yes screws M3x10

material only PETG ABS ASA infill 50% support yes resolution 0.2 4 bearing U 32mm hole 6mm 4 screws M6 2 screws M5 D nut

material ONLY Petg Abs Asa infill 60% resolution 0.2 support Yes

A 4020 adapter plate that uses no additional mounting gear and has a couple fan duct designs. In order to fit the fan you'll need to remove the grill that goes on top of the extruder, that is why I included a cable plate that bolts the same way...

So when I imported this into Prusa slicer it didnt orient properly so I centered it properly and then did some changes to the file that I think makes it looks better... its not perfect but it works for me....the build plate is set for 230mm i can do...

fan 5015 24v infill 40% petg no support

it is preferable to print it at 30 ° or 45 ° to give more strength to the piece due to anisotropy

These are the parts needed to add linear rail on the X axis. Designed the carriage myself and remixed the X tensioner from https://www.thingiverse.com/thing:2854971 to be as short as possible so that there is space for the linear rail (get the...

After replacing the 4010 original fan with a 5015 fan, this fan duct will be indispensable!

as described, a mount for webcams. Just unscrew the cableholder from the X-axis-gantry- stepper-housing and fit the printed piece inbetween. ...The webcam will now move up with the Z-Axis.

This is a Camera shell mount for Raspberry pi Side mount. Also look for the companion things of the Arms and Side Mount things. https://www.thingiverse.com/thing:4660347 and https://www.thingiverse.com/thing:4660358 These were remixed from the...

This cover for extruder block, replace the original one when you'll put a 5015 fan.

The resulting .bin file must be placed on the sd card COOLING SYSTEMS (Works also on D3 and D4): -FIRST ITERATION: 4010 stock blower fan -SECOND ITERATION: 4020 blower fan (much better) I'm curious to see your remixes This is my D2 cura profile:...

material only petg abs asa infill 60% resolution 0.2 support yes