mighty plus case 3d models

The printed parts are actually the same, it's just the front and rear panels that are different but I prefer to keep them apart for different reasons.For most user cases, one or two dryers should be sufficient but it depends on what type of filament...

Just in case, you can put 3-4 layers of office paper on the bed under the nozzle in the area of ​​\u200b\u200bthe home point 19. If you did everything right, then after warming up and moving the nozzle into the house, it will not touch the bed 20. A...

Note that because this mode requires disassembly of the printer, you may want to print several successive sizes of bearings in case your printer is slightly out of calibration, just to make sure that one set is “tight” enough for you to “hone” the...

just in case the original author decides to take it down for some reason.) https://www.thingiverse.com/thing:3579224The first 7 pieces replace parts in the original, so obviously dont print the originals of those. 8-11 are in addition to everything...

If the opposite is the case, i.e. rings fall apart, then either reduce spacing or print with fatter layers.</p> <p>Good results are obtained by coordinating OpenSCAD and slicer settings:</p> <ul> <li>using small spaces between rings (<em>spacing</em>...

Whatever you have to add (or subtract as the case may be) to the average in order to get 180 (or 0 or 360) is the number you have to generally add (or subtract) to compass bearings to get true bearings. If you need to go the other way, i.e. convert...

Thus, SCOPES is self-contained and can be operated in the complete absence of any infrastructure with just a mobile device and a battery. SCOPES 3.0 The boxSCOPE case is the latest revision of our original SCOPEScase. The original version can be made...

Both astromecs will compute astrogation data and each one will store at least 3 hyperspace coordinates to allow immediate retreat in case of emergency. Before flight they were to be permanently connected to ship's systems via their computer sockets...

Both astromecs will compute astrogation data and each one will store at least 3 hyperspace coordinates to allow immediate retreat in case of emergency. Before flight they were to be permanently connected to ship's systems via their computer sockets...

I have included the source file though, in case anyone wants to experiment, together with a peg handle that takes a length of 4mm rod - this holds the mount in place on the rail. [UPDATED 21-June-2019] I have tested the tracker using the sun - I...

But just in case any piece came out imperfect during printing, you can get the individual STL without the AIO prefix and re-print at ease.The grey color on the BVM is very dark and I've found the "Cerprise" Grey to be very close. You might want to...

“Flowing water wears away the stone”.I will separate each step assembly one by one for easier to work with, and the components included.If my calculation is correct that you will need to print about 50 cable chains link and chains cover.And here is...

Since it has a mounting for ESP32 it can be made as an IoT button therefore the sky is the limit.Additional use casesYou can use this as just a regular button and connect button/LED wires directly to a microcontroller.Can use ESP32 to have WiFi...

UNTESTED but should be noticeably “better”, see notes laterChanged the nut slots to hexagonal to more securely capture the nutsSlots instead of captured nuts in the spider (similar to several other remixes), spaced correctly for M4 pitch and 0.28mm...

I have only needed 2 in some cases but in most I haven’t needed them at all. You just need to make sure the side closet to the front is aligned properly to allow the lock to pass through easily. You will notice that there are two slightly different...

In a worst case scenario, mods like this one can flood your printer with resin! Be aware of the danger and check the system for leaks regularly. Test the system thoroughly with water before the first use!!!</p> </li> <li><p>I am not responsible for...

[NOTE: It is best to use a glue that gives you enough working time to slide the pieces after inserting all but the last border part(s), just in case…] &nbsp; *I did not need to glue my board, when I used these v6 pieces. They fit precisely into the...

Using the following options: qr_tolerance = 0.001 case_thickness = 1.8 tag_height = 80 obj = 0 qr_bottom = 1 hole_r = 10 hole_y = 0 hole_x = 30 qr_data = [0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,...

Unfortunately, with many tables, a large solid leg or lifting mechanism gets stuck in the middle under the table and you can't slide a chair up to such a table and sit with the legs under the table.So I made a coffee table that can be easily lifted...

Just refile it a bit with a cutter!Update 31/01/24I started the electronic part with some late.The main issue is my board (NodeMCU esp32 or esp8266 d1mini)Both have some high deep sleep current, almost 20mAh, so running it on battery is pretty...

instead other models of TMCxxx , No solder iron necessary, you just have to rotate the connectors receptacles on the motherboard with a simple leatherman tool.like on this video Be care, some of the latest motherboard doesn't have support under the...

In that case you need to ensure the gab is closed while gluing the socket onto the ring. When the ring is done and fully cured you can do another test run to see if the LED strip survived, but it is not required. If there is no visible damage,...

I included a slightly less than and slightly more than hole on the servo horns just in case you want a little more or less throw. Some might want more aileron for example like you would get from the stock hardware kit. On the rudder you may actually...

Customized QR code tag using Thingiverse's Customizer app: [http://www.thingiverse.com/apps/customizer/run?thing_id=46884](http://www.thingiverse.com/apps/customizer/run?thing_id=46884) Options used for this tag: - QR code size: 33mm - QR code bottom...

**Update 2022-10-03: After uploading this thing I opened a case with Thingiverse to report that the original was removed and they were very quick to respond and restore the accessibility of it.** **I'll leave this up for a while for anyone who liked...

Also it feels quite different to spin and creates a little rattling noise when spinning.In case you want to customize things, please install OpenSCAD on your own computer and follow these instructions to customize your ring.Thanks go out to ixpatch...

ESP32 pin numbers in code. You need: Power Led Open Led Close Led Open Microswitch Closed Microswitch Common GND for above Manual Open push button Manual Close push button Motor + Motor - So 8 wires in total. Manual buttons are fixed to the case and...

If you still have problems, then please visit the original thingieverse publication (https://www.thingiverse.com/thing:4267962) where I have added some custom parts for such rare cases. For the lamp shades including the lower and upper ring parts,...

I've also kept the motor separate from the pump jet in case you want to model your own motor housing for different motors. Note this design has inlet and outlets for water cooling, you will need to plug or remove these if not needed otherwise it...

 (Not surprising, but possibly indicative of some issues with “playability” at this scale?)  Here are the things I have tried, in each case:Issue(s)Things to check:Things to try:i) My ball does not always sit still when I place it on the table, or it...