micro swiss 3d models

This has been remixed for better fit with the Micro Swiss Direct Drive. The chimney has moved left, along with a bit of cable managing on the back. v1.1: 1. Errors in manifold have been fixed which would cause holes and gaps between layers when...

2 Adjusted Screw Hole Alignment, Added support wedges REV.1 Adjusted Thickness of clamp face and screw holes Files: -Custom_Nova_5015_Mount_Ezabl_Final_RTP -Clamp_For_Nova_Hotend This is A Custom mount to attach The Nova hotend to a Micro Swiss...

This is a hastily crafted adaptation of the hero me gen 2 tailored specifically for the mosquito hot end to be paired with a micro swiss direct drive extruder. Being entirely new to design, I relied on tinker cad to customize Mediaman's original...

[UPDATE: January 29, 2021] I remodelled the x-axis cover part so that the endstop cable is not squeezed between endstop housing and strain relief This is a re-mix of the cable management for Micro Swiss DD from FastIndy...

The one that he made works with the stock Ender 5, but recently I upgraded to a Micro Swiss direct drive extruder. The mount that he designed hits the spot where the belt is attached to the carriage plate. The mount doesn't hit the belt clip now...

Micro Swiss Direct Drive Extruder Only (part #M2602) or Micro Swiss Direct Drive Extruder and Hot End (part #M2601) Offset for my extruder: X= -48.5 Y= -8.5 Z= -1.75 to -2.10(set to -1.65 for the initial till you can find your Z Offset) Fits CR-10...

The stock BL Touch mount integrates seamlessly with the Micro Swiss direct plate, but be aware that removing the fan cover for any reason necessitates a check of your z-offset since they utilize identical screws. The MS mount boasts two unused...

I traced the Micro Swiss linear rail bracket from a photo after performing perspective correction on it, and it should be the correct measurements to make this work. The MS Linear Rail kit is quite a bit wider than the roller kit, or stock...

This is from https://www.thingiverse.com/thing:4975364 using the micro swiss all metal SE for the Flsun Q5 mod https://www.thingiverse.com/thing:4920704. Added V2: with better air flow and lowered even more. Added V3: moved the duct back more...

It was modified to fit with a Micro-Swiss dual gear direct extruder with hotend kit. I used some red silicon ptv to help seal it to the machined base. I didn't think I needed to drill and tap an additional hole. The h5 fans seem to be holding...

After installing my Micro Swiss NG I noticed the wires to the heater and thermistor moved while printing. I was concerned they would eventually break. I found redpiyaya's cable support but didn't want to have to remove the V-slot wheels to...

This is a remix of a remix of the fan duct, that will fit better (not perfect) if you have a micro swiss hot end installed. I'm not an expert (first remix) i took the existing model, i've put it in fusion 360, cut it in half and added 3mm on the Z...

Fan shroud for the Micro Swiss NG Extruder for CR-10 V2 and CR-10 V3. SKU: M3206 Cooling Fan (Hotend): 4010 Cooling Fan (Part-Cooling): 5015 This fan shroud does not get in the way or affect of the normal CR-10 V2 / V3 probe mounts. The...

*Note:* This fan duct has been designed for the Ender 5 Micro Swiss direct drive hot end. I don't know if it can be used on any other model. #Description This is a remix of JeffrayMK Satsana dual 5012 fan duct...

The Micro Swiss end was initially set up for the original drag chain's end mount, while the bottom rail mount was designed for the new chain end. If you prefer both chains to use the same mounting type, you'll need to modify the Micro Swiss end to...

It's possible that all I needed to do was raise the temperature or change some settings, but I bought a Micro Swiss hot end, found it to be 5.3 mm too short, modified the part that this design is based on and have since gone through several rolls of...

Designed this for those requiring a basic and reasonably compact Micro Swiss compatible hotend cooling duct modeled off Crealities Ender 3v2 OEM fan shroud with part cooling pointing either side of the nozzel using the two stock fans. You need to...

DEPRECATED DESIGN Please be aware I am not developing this design any further. This is v2, an upgrade I think to the previous version. Made of 5 parts that are much easier to print. Screw them together with M2.5x10mm Socket Head screws. Designed...

This is the Hero Me Gen4 base for the Micro Swiss direct drive extruder, as modded by Marcelofs13, with one key adjustment made. The location of a critical screw has been shifted to prevent sagging on the right side of the base due to high...

So I got my Micro Swiss direct drive and hot end upgrade but didn't like the cooler shroud that needed to be printed as it utilizes the single 40-10 part cooler fan. I wanted to increase my part cooling so i bought another 40-10 cooling fan and...

This is a complete conversion kit to Micro Swiss all metal hotend for Anycubic Chiron that fits perfectly to stock hotend backplate and can be used for those who changed homing to the right like I did or took out Z-endstops from their setups and...

This is a mount solution for the BTT Filament Runout Sensor when you have installed a Micro Swiss Direct Drive Kit. I combined the roller assembly from https://www.thingiverse.com/thing:3052488 with my own mounting solution on the X Mount plate. To...

These pieces will help mount a cable chain on a micro-swiss direct drive extruder, all the way to the Z/X axis rear bracket (ender 3 pro) without sacrificing printing volume/area.All the other mounts I found had the cable chain binding on the side or...

This cable chain is specifically designed for use with my Micro Swiss Direct Drive fan duct but can be easily adapted to work on other configurations. F3Z included Installation: Begin at the extruder and work your way back, adding 1-3 links at a...

Decided to make a cooler that fits directly to the Micro Swiss DD bracket as I wasn't happy with the other designs I found. Bigger cooling nozzles in prototypes allow for the part cooling to flow and not have as much static pressure. Didn't do...

After fitting my Ender-3 Pro with a Micro Swiss direct drive I found that the cables were floating around at the extruder end. I came up with the idea of printing a clip to attach to the extruder stepper motor that the conduit could be attached to...

Straight forward wire management links for an Ender 3 V2 with a Micro-Swiss NG direct drive extruder. I provided the STP files so anyone can edit them to their liking.&nbsp;</p><p>&nbsp;</p><p>You will need a total of 10 links. I used zip ties to...

This hotend fan duct is designed specifically for the Micro Swiss hotend used in Creality Ender 5 and compatible printers with stock hotend shroud. It prevents the hotend cooling fan from blowing directly onto the heater block, instead directing 100%...

I also uploaded one without the need for heat set inserts, if needed.I also uploaded my STEP file so people can easier amend the model to their printer models an needs.Printable without support.There is also a version vor the Ender 5 linear rails...

Remix of Ender 5 Plus Micro Swiss NG Cable Strain Relief by Tuna on Printables. Original was slightly too thick to use with the CR-10/Ender3 NG variant and would cause binding of the V rollers. Rather than thin it out, potentially losing some...