micro swiss 3d models

By not having a separate thermal tube inside the cooling block, it allows for faster heat dissipation.The thermal heat break is made from Grade 5 Titanium Alloy to provide excellent thermal isolation between the heater and the cooling block.Titanium...

This is a fast and dirty fusion 360 model based on the Micro Swiss NG direct drive. The adapter is made to allow the use of a 5015 blower instead of the stock blower fan. The print requires support. I used cura 5.0 with tree supports and it printed...

This is an interface plate created for the Micro Swiss NG for use with the Wham Bam MUTANT V2. printed at 0.2 layer height. You will need 5 x 3 mm threaded inserts that come with the MUTANT kit Two versions available. Version A: ...

This design is to allow cable management for a Micro Swiss Hotend & Direct Drive set for the Ender 5. The cables are guided to the back into a chain to finally connect to the frame. The main adapter needs to be printed with support. The...

I'd been relying on _3DDP_'s fan ring with my Ender 3 Pro, but after acquiring and installing a new Micro Swiss all-metal hot-end, the existing fan ring was no longer compatible due to the different offset of the nozzle. I transferred _3DDP_'s design...

I used the KentoHardRok adapter to perform my Micro Swiss direct-drive upgrade to my CR10S Pro v1 and found that that both mounts for the BLTouch referenced from the remixed design exceeded the sensor offset limits on the firmware used. I modeled a...

Mounting plate for use on the Micro-Swiss direct drive extruder plate for the DyzeEnd X hotend. Will work with water cooling, or air-cooled with the stock Dyze Design cooling fan. Uses the stock Ender 5 BLTouch mount and hardware. You will need...

... The Y component replaces the holder that normally secures the Y switch, while the X part slips over the new micro Swiss aluminium piece where the x limit switch makes contact - secure it in place with a small amount of super glue for stability.

... with spacers to adjust the Z. On the Micro Swiss Direct drive there was no need for the cut out area so I removed it to increase strength. This will print with no supports . ... Settings Y: -17.5 mm X: -43.8 mm and Z will depend on spacers used.

Fang base plate for the Micro Swiss Direct Drive + MS Hot End (Ender 5 Version). Use the following "fang"-duct: https://www.thingiverse.com/thing:4389912 ...and for the 40mm fan: https://www.thingiverse.com/thing:2763931 Offsets: x: -54 ...

This takes @OpenDorrPolicy's adapter, which lets you mount the Ender 3 Max fan shroud on the Micro Swiss Direct Drive extruder plate, and adds a mount for a BLtouch probe, using the same L-bracket as would be used on the stock Ender 3 Max. You...

I recently picked up a Micro Swiss 300c Hot End, and the mount I had been using on the stock hot end no longer fits properly. I modified the STL file in Tinkercad to get a snug fit that works for me. If you experience any problems with this design,...

The stock BL Touch mount works seamlessly with the Micro Swiss direct plate, except when removing the fan cover becomes necessary due to any reason. In such cases, it's crucial to verify your z-offset since they employ the same screws. The MS mount...

I made this custom part for my Micro Swiss all metal hot end because I love the high clearance that the fang offers, but unfortunately, it wouldn't fit my brand new hot end. I printed mine at 0.2mm height with PETG and it turned out to be a very...

Made a simple bracket to manage the cables for the Micro Swiss Direct Drive one thing I needed to do was when mounting the bracket on the motor I had it more to the right of the motor so the cable would clear both upright post Update 12-26-2020: made...

This is a mount for those who want to use this fang (the reversed one) for Micro Swiss Direct Drive. Its made for Ender 5 but i suppose it fits the others to. Also room for a BLTouch https://www.thingiverse.com/thing:3091560/files And this file...

This is an upgrade for my Micro Swiss Direct Drive EZOut v2 Mount: https://www.thingiverse.com/thing:4232736 Step files are included. This installs between the EZOut Mount and the Bowden Tube on that mount. Insert a small amount of cotton or...

With the Micro Swiss direct drive extruder on the Ender-3 printer the Z-axis is somewhat reduced. ...With this cable chain mounts the cables and filament are running in front of the frame so you can achieve 200mm build height.The top and bottom parts...

I needed a BL Touch mount for the Micro Swiss NG so i made one. I used the original shroud screw for mounting it to. ...I also used some longer M3x12 screws with a nut to mount the BL to the adapter Offset i used was x -50 y -7 it rubs slightly when...

I traced the Micro Swiss linear rail bracket from a photo after performing perspective correction on it, and it should be the correct measurements to make this work.The MS Linear Rail kit is quite a bit wider than the roller kit, or stock bracket, so...

I was using https://www.thingiverse.com/thing:4742800 with stock ender 3 v2 but upgraded to Micro Swiss NG direct-drive and hot-end. I wanted to reuse the endoscope holder I had already and just mount it to this fan shroud. ... This endoscope is...

The Micro Swiss hotend performs perfectly, whereas myself and others I know have encountered numerous issues with the Monoprice factory hotend. No new hardware is required. Simply print the backplate with supports oriented upwards, while the...

I installed this on a customized Longer LK4 Pro (sort of an Ender 3 clone), hence it should fit any Ender 3 version that has been modified with a Micro-Swiss Direct Drive extruder, and probably other printers as well. I used standard 40x40mm...

Micro Swiss Direct Drive Extruder Only (part #M2602) or Micro Swiss Direct Drive Extruder and Hot End (part #M2601) Offset for my extruder: X= -46.00 Y= -9.00 Z= -1.75 to -1.90 (set to -1.65 for the initial till you can find your Z Offset) Fits...

The Micro Swiss manual states that the cold end should protrude 1.7mm, so I've made the MK2 1.7mm available with or without support. I've downloaded and tested a few of these drive plates, but none of them worked for me. I'm printing with the...

Nuts have inset spaces where they can be press-fit, or if resin printed, locked in with some cyanoacrylate glue or resin set with a UV light.Two variants of the Fan Block exist - one for a 4010 fan, and one for a 4020 noctua or similar.The mounting...

I installed this on a customized Longer LK4 Pro (sort of an Ender 3 clone), hence it should fit any Ender 3 version that has been modified with a Micro-Swiss Direct Drive extruder, and probably other printers as well. I used standard 40x40mm...

Upgrading to the micro Swiss direct drive kit for the Ender 3? This extruder knob reclaims the original brass extruder gear as its core component. I grew weary of extruder knobs relying solely on plastic contact points, which can be easily rounded...

I installed the Micro Swiss All Metal Hotend on my Ender 3 and initially encountered issues when I hastily assembled the fan duct. A sudden shock jolted me awake in bed, prompting me to revisit the Gabriel3DCaster design that I'm grateful for. To...

Designed to use with Micro Swiss Direct Drive Base for Ender 5. As a bonus - now it is so easy to operate extruder's spring arm. Screwed to the base using 2x m3x12 screws Needed to attach a 3/4 inch [split wire loom...