micro swiss support 3d models

Swiss Tool

<img src="http://nebula.wsimg.com/01c37ede5107382dac843255bf1665fe?AccessKeyId=D78877820DACAFA338E2&disposition=0&alloworigin=1" width="600" height="100"> <font size="2" color=brown>http://www.petsfang.com/</font> ***** ***** Use the...

This is a remix of the "cable chain end" extruder clip by sebho85 - I corrected the position of the cable chain connector on the extruder clip because the whole cable chain was not properly aligned and therefore is twisted a bit. This twist can lead...

I had a hard time finding a cr touch mount for the bondtech ddx that was higher than the print nozzel, i modified this to have the proper offset and it fits perfect with the microswiss hotend

I noticed that this design had not been properly adapted to the CR Touch without anything extra added onto the design and decided this would be very useful considering the benefits of the CR Touch compared to the BL Touch. The probe offset should...

This is a remix of eecue's remix, I've taken away some material to make it lighter. This one is for 4010 fan and CR touch. ... Offset for my extruder: X-45.15 Y-8.28 Z-2.40

This is a remix of the bracket that came with the upgrade kit that goes where the extruder was before the direct drive upgrade for cable management

Moved the 3d touch/BL touch out 5mm so you can fit other way round

This is a guid to make the MicroSwiss Linear Rail Direct Drive kit work on your Ender 5 You need to buy some M3, M4 bolts, 4x 683ZZZ 3x7mm bearings and some t-Nuts 2 belt spacers, one end stop holder needs to be printed and if you like to a...

bei den 2 Bohrungen kommen noch 2 Gewindeeinsätze M3 rein, damit es dann auch verschraubbar ist. Infill hab ich mal auf 50% gesetzt damit die Gewindeeinsätze auch gut halten, das ganze wird dann mit dem ExtruderFan mitangeschraubt. ... PLA 0,2Layer ...

For the hotend cables I used a big Self-Closing Cable Sleeve Cover Cable Management. I first drew the piece, then printed it and used it to drill the two 2.5 mm holes on the back plate of the MS NG and finally tap 3mm, which leaves the first...

a low profile twist on this minimal knob

This is remixed to an have an 18mm z axis cable chain so that the rasberry pi cam cable can be fed through the arm and down to the chain to the control enclosure.

Created cutout for CRTouch. Original remix only worked with BLtoch. ...This will fit both.

Permanent mount for the Adafruit ADXL345 that attaches to the front fan. ... You will need to replace the stock screws wit 20mm M3's

I didn't want to lengthen any cables so I borrowed from Eric's design and added a few bits of my own. It works well. ... PS: This was installed on an ender 3 v2 which has different cable routing than an ender 3.

A fusion of remixes from https://www.thingiverse.com/thing:4369859, further reworked in https://www.thingiverse.com/thing:4408571 and https://www.thingiverse.com/thing:4422069. This custom creation, adapted from the MS direct drive remix, now...

I used the original remix of [Akanar](https://www.thingiverse.com/akanar/designs) for a while. It fits really good :) Like often there is a "but". Akanar designed the remix for Microswiss DirectDrive "first version / generation". Thanks to...

mounts to left shroud mount. will need to change the m3 bolt to a m3x8mm and 2 are needed for the cr touch. i did find that i needed to place a nut at the bottom of the v2 mount to allow for clearance. this is my first attemp and think i will do...

I wanted to use this for my printer but did not want to cut and rewire everything. So this is a remix of the link with a removable clip harkening back to johnniewhiskey's design. ...For the other three pieces, I didn't bother remixing and just printed...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

I took kalrog2's idea and redesigned the modular 5015 blower adapter from scratch to be a bit more robust and optimize the airflow a bit while keeping all four screwholes usable for fixing the blower to the shroud. This is already updated to v2...

I needed a duct and didn't like the bulkiness of the ones available so i made one a little more compact. ... Its definitely still a work in progress.

Hobbled together something that will work to properly allow the NG extruder to hit the X-Axis limit switch on the Ender 3 V2 Neo from Creality. ...The switch style is that of the Ender 3 S-1 model which lays flat instead of vertical.

Removed some extra material that was preventing the clip from properly sitting on the stepper motor. Since the motor has differing dimensions for the black vs silver sections, the original did not fit quite right. I also removed a portion of what...

this hotend block replaces the original block. Thanks to the larger front fan, it greatly improves the cooling of the hotend, allowing you to obtain quality prints and extend the life of the hotend. Thanks to the excellent cooling of the extruder it...

Thigiverse was having trouble associating this with my other designs so it has been moved to: https://www.thingiverse.com/thing:4775320 You can still use this spreadsheet, Files to print: ...

Just dropping this off for now, I'll get back to adding BOM as soon as possible. These brackets enable the use of a Bondtech BMG extruder (use the Mirrored version) on the Mamorubot SX-4 CORE XY machine. One of the brackets also converts the front...