micro swiss support 3d models

I couldn't find the .stl file for the 3D printed extruder bracket that is supplied with the Micro Swiss Direct Drive extruder kit, all design rights belong to Micro Swiss, I merely reproduced it so I could print it in a choice of my colour. I also...

I used the screws provided by Micro Swiss to fix it to the shroud and M3's with nuts to attach the fan to the adapter. Zip ties also work quite well. V1.1 has a split airway to diverge the air in both directions. V1.2 is completely open. ...I tested...

It attaches to the Micro Swiss hot end to give a more accurate reading of the resonance frequencies at the extruder tip. Requires 4x m3 screws, either 4mm or 5mm. Might fit on other hotends, but might require some tweaking to fit. ...Remove hot...

Despite having no prior experience with Tinkercad, I decided to try modifying it for the Micro Swiss hot end. The initial designer deserves all credit for their work. My contribution was merely extending the bracket in a somewhat crude manner. ...The...

Designed this fan duct to direct the airflow through the Micro Swiss hotend heatsink with added simplicity over other fan shrouds. I wasn't looking to print out bulky fan ducts with many components and wanted a part I could print in one go. Look...

... meticulous measurements as no other options available online matched the level of accuracy I was seeking. This is the exact version I utilized: https://store.micro-swiss.com/collections/all-metal-hotend-kits/products/all-metal-hotend-kit-for-cr-10

After trying several extruders, I purchased the Micro Swiss extruder. When I installed it, I found the layout was reverse of stock and the runout sensor did not align correctly. I could not find a setup that I was looking for, so I found one that was...

This is a modular cooler for the CR-10 with a Micro Swiss hot end that combines functionality with ease of use. Both fan mounts are installed without screws, allowing for quick removal for maintenance on the hot end. To install the hot end cooler,...

=========================== this model wont cover the inner two micro sd card slots like the unremixed model did. ------------------------------------- this model is also smaller in every dimension but still has good proportions. requires two m3...

... The airflow and cooling are significantly improved. The clever design draws inspiration from Chris Kissling's Sapphire S base. Check it out here: https://bit.ly/2Rp5zK1 When printing the fan ducts, be sure to use supports for optimal results.

Test

Micro Swiss Linear Rail Direct Drive - BLTOUCH Mount

This cooling case works with an 4010 fan. ...Connect the fan with the hotend fan. Print it with support and support blocker. I printed it with PETG. Works fine. Temperature Micro Swiss Extruder is constant 32 degrees. ...

This mount has been designed to allow the Micro Swiss / CR10 hotend to attach to the Tevo Tarantula, it also supports the SN04 Sensor. ...This is designed to take 3mm brass inserts where the hot end would mount

Direct drive extruder adapter remixed for use with a Micro-Swiss extruder. Print laying flat on its back with support. ...I would recommend 100% infill on at least the screw part.

This remix supports the Minv2 Fan Mount installed on the Micro Swiss Direct Drive kit with precision engineering. ... The clearance between the blower fan and extruder motor is snugly tight, yet operates seamlessly without a hitch.

a quick and simple hotend wire strain relief for the micro swiss ng

two variants of hotend cooling for micro swiss hotend for CR10 and similar

Micro Swiss themed 40mm fan guard. ... If you are looking for the entire fan shroud and part cooling fan duct for the Micro Swiss direct drive kit, see here: https://www.thingiverse.com/thing:4934569

Shifted a bit to each side to make room for the Micro Swiss extruder instead of stock

Designed to fit Micro Swiss Direct Drive and allow you to secure your BLTouch to the aluminum frame

Satsana for the Micro Swiss Direct Drive with a BLTouch on the Ender 3 doesnt matter what model and whatever other models the Micro Swiss Direct Drive fits. ... I redid this Mini because the Swiss Hot End loves this Satsana, the fan blows onto the...

The modified base was specifically designed to accommodate the micro Swiss direct drive, which has a slightly greater thickness than the standard mounting plate found on Creatliy printers.

Swiss army knife style holder for micro sd cardsRequires two M3 screws, M3*12 fit three layers, M3*16 fit five

Micro Swiss all metal hotend mount for Prusa mini. ... Requirements: 2x M3 inserts to mount the fan 1x insert to mount pinda Various M3 nuts and bolts

Couldn't find a good way to make the cables look clean after installing a Micro Swiss direct drive on my ender 3v2 so I made this.

Compensates for the 5mm offset created on the X axis after installing Micro Swiss Direct Drive, can be used with BL Touch. I used PLA, no supports, yes raft. You will need a spare 3*8 screw (same screw used for the stock fan shroud. ... This does not...

This is the extruder knob Micro Swiss suggest you use in there manual made by ReplayMD on Thingiverse. ...https://www.thingiverse.com/thing:2776404 I remade it to fit the Satsana fan shroud for the Micro Swiss Direct Drive that I extended.

This is a part cooling duct for 40X10 or 40x20 fans designed to be mounted to Rimba's Hot End cooling duct for the Micro Swiss direct drive kit on the Creality Ender 3 and compatible printers: https://www.thingiverse.com/thing:3808538 This duct will...

I love the look of pixel2's extruder knob, but as designed it does not fit the Micro Swiss extruder I installed on my Ender 5 Plus as the “stem” part is too thick and is obstructed by the tension gear pivot. I did this very simple remix to make it...