micro swiss support 3d models

The whole body is screwed together, which makes printing quick and simple and you don't need to use support. By not using the original metal housing for the fans, the saved weight can go into a second blower fan. The total weight of my cooling...

Micro-switches are used to activate and deactivate the ventilation system in the enclosure when the door is opened or closed. ... Reference micro-switch: B3-13131 or M8805/101-021

The Eachine Tyro99 drone boasts a built-in Firefly micro camera that captures stunning footage from the air.

PC4-M10 extension: /Quality-0.1mm, line width 0.4mm, wall width 0.4mm (see attached Cura 4.11.0 settings); /Infill-40%; /Top/Bottom-ironing on all surfaces /Support-no, hex shape on the top. Hot end fix: /Quality-0.1mm; /Infill-40%; /Support-no;...

Also, i advise to print them with SX and DX markings facing down, using supports, in order to have clean mating surfaces for the motor and the extruder body.Give it at least 2 mm shells where possible and a good amount of infill density, with a...

Print with support because the bolt tab is elevated slightly for fit. Back Plate - Removed some material to allow air to exit Extruder Knob - Original design. Compact with a locking bolt/nut. Visible from the front for viewing from a webcam. It...

Print with support because the bolt tab is elevated slightly for fit. **Back Plate** - Removed some material to allow air to exit **Extruder Knob** - Original design. Compact with a locking bolt/nut. Visible from the front for viewing from a...

To solve this problem, I designed a simple clip-on support for the Micro USB cable. It's perfect for smaller, slimmer cables, but may not work well with chunky ones. The print is fast and uses little filament, so it's worth trying out! I've included...

This is a remix of the Kobra Max Direct Drive Mount . Everything fits well and doesn't flex unnecessarily. This is designed to fit the stock stepper motor and extruder. I replaced with a pancake stepper to reduce weight. To assemble: ...

This is a simple hotend wire harness for the new MS DD NG. ...You need to install this prior to installing the V-Slot wheels.

Main page: https://www.printables.com/model/218461-voron-revo-mount-and-fanducts-v2

Excuse the poor photos! ADXL343 (Cheaper than 345) mount for the new MicroSwiss NG extruder. A little overkill with heated inserts but hold solid to get an accurate reading. These are the brass inserts I used: ...

Print using PLA. .2 layer 205 Deg Nozzle for layer adhesion. Use M4 pan heads for clamping. Cuts 60 deg tip and 49.0 length using single side craft razor blade. ...

Extruder housing BMG Style with MicroSwiss parts, to use as bowden extruder. ... To use M6 + M10 / 1/8BSP Bowden Couppler

This modification enables the utilization of the CR10 or MicroSwiss full metal hotend on the Anet A8, AM8, or PK8. The auto-bed leveling sensor is an 18mm capacitive sensor. ...For the X belt, I employed this belt holder:...

I remixed this Satsana fanduct to remove 2 faces and 2 holes from old 4010 radial fan. ... https://www.thingiverse.com/thing:4837565

Excuse the poor photos! ADXL343 (Cheaper than 345) mount for the new MicroSwiss NG extruder. A little overkill with heated inserts but hold solid to get an accurate reading. These are the brass inserts I used:...

cr-touch mount for a MicroSwiss NG extruder. Printed in PETG Printed it on high infill settings, 40% infill, wanted it really sturdy but that's probably unnecessary. Installation tip Start by installing the mount to the extruder else you won't...

Another fan duct to replace the default on version one pro. ...has been working nicely on my machine

just need a set screw

I only had some smaller 35mm fans, so I tweaked this design so the fans could just press fit in, with no screws needed.

Das ist ein Remix von https://www.thingiverse.com/thing:4101494 und https://www.thingiverse.com/thing:4389912 Habe nur die Öffnung etwas vergrößert und eine Halterung für die Kabel eingefügt, damit sie nach links liegen. ...

A Customized Upgrade for Creality Printers: A Fresh Twist on the Snap-On Fan Duct by RaffoSan. https://www.thingiverse.com/thing:2612897 Following extensive research into fan technology, I decided to test the effectiveness of internal guide blades...

Here is a custom-built Nozzle box specifically designed for your Nozzles, crafted without any pre-installed markings to accommodate various nozzle sizes, allowing for easy future customization and adaptability.

Please post my makes. MicroSwiss 300 I mounted a 10mm fan spacer. ...The fan should attach to the outside.

This project ultimately came about from trying many different setups from other users. While I liked all of them, there was always something I wasn't super happy with or new features I wished they incorporated. This system is also compatible with...

sonic pad accelerometer mount for the hot ended cooling fan

Decided to purchase the Sapphire Pro after watching may reviews. As part of the build I decided to include a better hotend and of course this meant modeling up a new mount. The design is simple but effective and has been working great. The...