micro swiss support 3d models

Printer: Creality CR-6 SE and CR-6 Max Extruder: Micro Swiss Dual Geared Bowden Extruder FilamentSensorAdapterCR-6-2Screws.stl - Extends the baseplate to allow for both of the original mounting screws to be used to secure the adaptor. I created...

Finished / Final / Last Version New Coldend Adapter 4 All Online Only One Fanbase For All Heads Sorry I'm Still A Beginner, Not Nice But Stable Original Base From Https://Www.Thingiverse.Com/Thing:2494642 - Wonderful Work - Thx New Fan Base 4 Stock...

I wanted a way to connect my drybox to my Ender 5 Pro's Micro Swiss Direct Drive extruder setup with Bowden / PTFE tubing, without running one super-long tube. The benefit of this is that it provides some support and strain relief while making it...

In addition to the SKR board, Micro Swiss extruder, BLTouch, and 5015 radial fan, you will also need the following hardware: 1 x RepRapDiscount Full Graphics Smart Controller LCD. The connector for the stock display is not compatible with the SKR...

A set of cable chain attachments to provide an x-axis chain for an Ender 3 printer with the Micro Swiss direct drive extruder kit. The cable chain attachments are compatible with the johnniewhiskey cable chain...

my remix of the micro swiss NG shroud for use with a 5015 blower fan. Should be compatible with CR10, CR10s, CR10s Pro or similar with a 5015 fan. Updated to remove excess nut retainer to allow mounting screw to be directly accessed in rear,...

This mount is designed to securely attach the Swiss-Micro hotend to the CR-10S, while also replacing the stock hotend fan and partcooling fan with high-performance 40mm Noctua fans. The model was carefully crafted in Fusion360 and thoroughly tested...

This is designed to house a 40x40x20mm cooling fan on an Ender 5/5+ with the Micro Swiss Direct Drive kit. This shroud includes a BL Touch mount, and a parts cooling duct. The cooling duct is 5mm lower than stock as the DD kit lowers the hotend...

... onto the printing surface, preventing airflow over the nozzle. This setup helps maintain the correct temperature and prevents jams, especially with micro Swiss Hotends featuring hardened steel nozzles. ...It's also compatible with the stock hotend.

I ended up getting the Micro Swiss Dual Gear Extruder and saw that I needed to print a part in order for the filament to line up from the run out sensor on the Ender 5 plus. I couldn't find one so I had to make one. This is a very simple design...

Since I upgraded my Ender 5 with Micro Swiss Direct Drive and Satsana duct I've been looking for a perfect extruder knob. I tried many knobs but wasn't really happy with any of them. I really liked this oversized design by caganseval...

Vintage-style micro racing suspension supports for CorSaIn's avant-garde vehicle designs.

Support micro pour icom 7300 ou 9700 Attention a la longueur des vis !

Support pour un shield Arduino Micro avec 1 Sabertooth 2x12 (Kit 2 DOF 120W)

Filament Runout Sensor adapter for installing the Micro Swiss Bowden Extruder on a Creality CR-6 SE or CR-6 Max. Printer: Creality CR-6 SE and CR-6 Max Extruder: Micro Swiss Dual Geared Bowden Extruder FilamentSensorAdapterCR-6-2Screws.stl - Extends...

... and this shroud, there are recesses in the model. In addition, I've left the outboard strain relief tab from the original Satsana model. This will not clash with the Micro-Swiss direct drive and I added holes for you to get a zip tie through.

Other than that, everything else is the same as the original Micro Swiss design. Settings: - Supports: Yes (touching buildplate only) Everything else is up to you according to preference. The settings I used specifically are listed below. ...

GERMAN ------------------------------------------------------ Kreation für den Creality Ender 3 V2 und dem Micro Swiss Direct Drive Extruder. Die Kabelkette wurde dabei auf der Vorderseite verlegt. Für die Befestigung der XY Kette habe ich eine...

I opened up the space for the hot end heater and thermocouple wires to run up the shroud, I found the old design putting stress on them in order for the shroud to sit flat on the micro swiss mount. I also found I was barely hitting the extruder arm...

This is a drag chain mount from the Ender-5 Plus frame to the X-axis where the drag chain is mounted behind the stepper motor on a Micro-Swiss direct drive mount. You would need the following set of screws and nuts to make this work. To mount the...

It's for the micro swiss direct drive kit for Ender 5/pro/plus. You have to dismantle the original fan housing and place this base instead and fix it with 4x M3 screws. Two on the left side over the bl-bracket. Two on the right side in the unused...

I needed a mount for stock fan on my Ender 3 Max for the Micro Swiss Direct drive extruder. holmes4 had one listed for a BL Touch but the mounts didn't line up. But I'd like to thank him for the inspiration. I have a CR Touch and I wanted it on the...

I was looking around for a runout sensor since I upgraded my Ender 3 Pro with a Micro Swiss Direct Drive and found the design by Sulfu, which is quite smart. It utilizes an optical sensor and is compatible with transparent filament by implementing...

This is my slowly and gradualy desgined cable chain for my beloved Ender 5 with Micro Swiss Direct Drive.thIt is a remix of very sturdy chain for Ender 3 by Diogo Santos https://www.thingiverse.com/thing:3715002and some Nema17 motor chain mount I...

This is my slowly and gradualy desgined cable chain for my beloved Ender 5 with Micro Swiss Direct Drive. It is a remix of very sturdy chain for Ender 3 by Diogo Santos https://www.thingiverse.com/thing:3715002 and some Nema17 motor chain mount I...

I found that the STL's Creality provided for mounting the accelerometer packaged with their Creality Sonic Pad would not work with a Micro Swiss NG so created one. With very little area on the NG for a mount to work, I chose to utilize the screw...

One of these was the Micro-Swiss all-metal hotend kit. This greatly increased the smoothness of the filament flow compared to the standard head. However, after a while, the Bowden tube kept popping out of the top, as the clip that holds it in isn't...

I needed a mount for stock fan on my Ender 3 Max for the Micro Swiss Direct drive extruder. holmes4 had one listed for a BL Touch but the mounts didn't line up. But I'd like to thank him for the inspiration. I have a CR Touch and I wanted it on the...

This is my slowly and gradualy desgined cable chain for my beloved Ender 5 with Micro Swiss Direct Drive. It is a remix of very sturdy chain for Ender 3 by Diogo Santos https://www.thingiverse.com/thing:3715002 and some Nema17 motor chain mount I...

Just my design of a fan bracket to Direct Drive Swiss, you need glueing 2 fans (Stock ender 3 V2), Screw M2 35 mm