micro swiss ng 3d models

This is an adapter to fit a 5015 blower fan to a Micro Swiss NG extruder/hotend. It is angled forward a little to allow the fan to clear the y axis belt tighteners. ...The back fan hole also lines up with the original screw hole which, along with a...

Print this to adapt a 5015 blower fan to the Micro Swiss NG shroud if you do not want to print a full shroud. This can be printed in PLA since it is just a fan mount. I used the screws provided by Micro Swiss to fix it to the shroud and M3's with...

a quick and simple hotend wire strain relief for the micro swiss ng

mod for micro swiss ng for the voxelab aquila estop. my stepper motor was in the way of getting to the estop. It attaches to the bltouch holes. ...I used the screws from the stock extruder.

Micro Swiss NG Dual 5015 Fan Shroud with CR Touch Mount.This is a work in progress, I have not printed this myself yet as I don't have 2 5015 fans to test with, yetOffsets for probe to nozzleX 93.2mmY 6.8mm

BL Touch bracket for Ender 6 with Micro Swiss NG direct drive extruder. Clears printer belt brackets. Uses M3 screws and nuts. Probe offset: M851 X-48.00 Y15.00 Z-4.10 Credit to DevDav I used his back plate to build off of.

I only have 5015 fans for my part cooling, so this is my attempt to adapt one to work with the Micro Swiss NG Direct Drive Extruder. Lay the model flat on the surface with the mounting holes, print with supports on the build plate only. I used...

The design is much easier to mount than the other designs I have come across and is a good option if you want to mount your cable in the positon shown in the pictures.Note that there are other designs around on the internet so try searching "Micro...

Dual 5015 fan shroud for micro swiss NG Designed for use on ender 5 so no print volume is lost with dual 5015 part cooling fans - Created because other dual 5015 shrouds out there reduce available print volume on ender 5 Files available for 4010 and...

I made a cooling fan shroud for the Micro Swiss NG Direct Drive extruder for my Ender 3 V2. It's designed for a 4020 axial fan to replace the loud 4010 axial fan on the front. Also to replace the 4010 Blower fan with a more powerful 5015 blower fan....

This is a remix of the Micro-Swiss model which retains all of the critical geometry, but greatly simplifies the model by removing the fillets. ...This is meant to serve as a starting point for further customization without having to deal with the...

This is a remix of the Micro-Swiss model which retains all of the critical geometry, but greatly simplifies the model by removing the fillets. This is meant to serve as a starting point for further customization without having to deal with the...

I used the mount hole locations from the "KUSBA mount for spite" and used the mount holes from the "adxl343 mount for microswiss" for the location on the NG extruder. ... Can be either used as a press fit as it holds quite well or use a 12mm long...

cr-touch mount for a MicroSwiss NG extruder. Printed in PETG Printed it on high infill settings, 40% infill, wanted it really sturdy but that's probably unnecessary. Installation tip Start by installing the mount to the extruder else you won't...

ADXL343 (Cheaper than 345) mount for the new MicroSwiss NG extruder. A little overkill with heated inserts but hold solid to get an accurate reading. These are the brass inserts I used: ...

ADXL343 (Cheaper than 345) mount for the new MicroSwiss NG extruder. A little overkill with heated inserts but hold solid to get an accurate reading. These are the brass inserts I used:...

Compatible with:Extruder :SKU M3205 - Micro Swiss NG™ Direct Drive Extruder for Creality Ender 6 PrintersHotend: Micro Swiss All Metal HotendHotend Fan: 4010Part Cooling Fan: 4010 BlowerProbe: none3D Printer Model:Ender-6

... be seen. It certainly won't be perfect. It doesn't look perfect, but not too bad for my first attempt. Please post a 'make' if you give it a try. https://store.micro-swiss.com/collections/extruders/products/micro-swiss-ng-direct-drive-extruder

BL-Touch/CR-Touch mounting brackets for the Micro Swiss NG Extruder and NG Revo Extruder installed on an ExoSlide motion system.The probe bracket for the regular NG Extruder is different than the NG Revo Extruder probe bracket so print the probe...

Fan Shroud for Micro Swiss NG Direct Drive Extruder for Creality Ender 6. Compatible with: SKU: M3205 (Ender-6 NG Extruder) Use support from build-plate only. Print using PETG, or a more heat-resistant filament. ... MS_NG_ESTEP400.gcode sets the...

This is a fast and dirty fusion 360 model based on the Micro Swiss NG direct drive. The adapter is made to allow the use of a 5015 blower instead of the stock blower fan. The print requires support. I used cura 5.0 with tree supports and it...

This is the x axis cover and mount for the Voxelab aquila adapted to fit the 'Micro Swiss NG Direct Drive for ender 3' carriage. ... It has the same dimensions as the original cover, but is cut out so that the switch is exposed and the stepper motor...

This is a remix of the Micro Swiss NG shroud https://www.thingiverse.com/thing:5358828 for use with a 4020 blower fan. So, it is fully compatible with CR10s Pro V1 & V2 fan's. I also modified the top right side of the shroud to place the...

This is an interface plate created for the Micro Swiss NG for use with the Wham Bam MUTANT V2. printed at 0.2 layer height. You will need 5 x 3 mm threaded inserts that come with the MUTANT kit Two versions available. Version A: ...

This is a fast and dirty fusion 360 model based on the Micro Swiss NG direct drive. The adapter is made to allow the use of a 5015 blower instead of the stock blower fan. The print requires support. I used cura 5.0 with tree supports and it printed...

I needed a BL Touch mount for the Micro Swiss NG so i made one. I used the original shroud screw for mounting it to. ...I also used some longer M3x12 screws with a nut to mount the BL to the adapter Offset i used was x -50 y -7 it rubs slightly when...

I was using https://www.thingiverse.com/thing:4742800 with stock ender 3 v2 but upgraded to Micro Swiss NG direct-drive and hot-end. I wanted to reuse the endoscope holder I had already and just mount it to this fan shroud. ... This endoscope is...

Fan shroud for the Micro Swiss NG Extruder for CR-10 V2 and CR-10 V3. SKU: M3206 Cooling Fan (Hotend): 4010 Cooling Fan (Part-Cooling): 5015 This fan shroud does not get in the way or affect of the normal CR-10 V2 / V3 probe mounts. The...

I also uploaded one without the need for heat set inserts, if needed.I also uploaded my STEP file so people can easier amend the model to their printer models an needs.Printable without support.There is also a version vor the Ender 5 linear rails...

Remix of Ender 5 Plus Micro Swiss NG Cable Strain Relief by Tuna on Printables. Original was slightly too thick to use with the CR-10/Ender3 NG variant and would cause binding of the V rollers. Rather than thin it out, potentially losing some...