micro swiss hot end 3d models

Couldn't find a good way to make the cables look clean after installing a Micro Swiss direct drive on my ender 3v2 so I made this.

Micro Swiss all metal hotend mount for Prusa mini. ... Requirements: 2x M3 inserts to mount the fan 1x insert to mount pinda Various M3 nuts and bolts

This is the extruder knob Micro Swiss suggest you use in there manual made by ReplayMD on Thingiverse. ...https://www.thingiverse.com/thing:2776404 I remade it to fit the Satsana fan shroud for the Micro Swiss Direct Drive that I extended.

This cooling case works with an 4010 fan. ...Connect the fan with the hotend fan. Print it with support and support blocker. I printed it with PETG. Works fine. Temperature Micro Swiss Extruder is constant 32 degrees. ...

Direct drive extruder adapter remixed for use with a Micro-Swiss extruder. Print laying flat on its back with support. ...I would recommend 100% infill on at least the screw part.

Simpler Knauf for Micro Swiss Direct Extruder with Direction Indication, since this works in reverse to the normal Extruder. ...Printed with the following Settings: Layer Height 0.12mm Filling Lines 20% Material PETG Gray (Amazon)

... instructions to install the DDX. Bondtech DDX https://www.bondtech.se/en/product/bondtech-ddx-for-creality-ender-cr-10s/ Micro Swiss Hotend https://store.micro-swiss.com/collections/all-metal-hotend-kits/products/all-metal-hotend-kit-for-cr-10

mod for micro swiss ng for the voxelab aquila estop. my stepper motor was in the way of getting to the estop. It attaches to the bltouch holes. ...I used the screws from the stock extruder.

This remix supports the Minv2 Fan Mount installed on the Micro Swiss Direct Drive kit with precision engineering. ... The clearance between the blower fan and extruder motor is snugly tight, yet operates seamlessly without a hitch.

This is a guide/support tower that screws into a convenient, unused and tapped hole in the Micro Swiss Direct Drive carriage plate for the Ender 5. ... **You Will Need** - 1x M3-12mm screw and M3 nut - 2x zip ties

sonic pad accelerometer mount for the hot ended cooling fan

Made for Ender 3 v2 and ispired from Micro Swiss Direct Drive Hydra Fan Duct, but i think it's ok for all ender 3 models Install Notes: Install both Bases Install 40mm fan on the duct Place the duct in the right base and tighteen the screw until the...

Made for Ender 3 v2 and ispired from Micro Swiss Direct Drive Hydra Fan Duct, but i think it's ok for all ender 3 models Install Notes: Install both Bases Install 40mm fan on the duct Place the duct in the right base and tighteen the screw until the...

These are the 3 set ups: 1 - Micro Swiss Direct Drive and Stock Hotend 2 - Micro Swiss Direct Drive and Dragonfly BMS Hotend 3 - Micro Swiss Direct Drive and Dragonfly BMS Hotend W/ dual 4010 blowers Note: When mounting the BL Touch, the top...

Custom Fit Extruder Knob for Micro Swiss Bowden Extruder The knobs provided by Micro Swiss were all too loose, so I created a simple OpenSCAD file to generate a custom fit knob. Customizer parameters: - id: Inside Diameter - The inside...

This is my attempt of making a direct drive mount for a Micro Swiss hotend, most of the assembly is printed in PLA but the Micro Swiss mount is printed in PETG. The belt tensioner is a modified version of the piece made by...

This is a remix of the Micro-Swiss model which retains all of the critical geometry, but greatly simplifies the model by removing the fillets. ...This is meant to serve as a starting point for further customization without having to deal with the...

Micro Swiss NG Dual 5015 Fan Shroud with CR Touch Mount.This is a work in progress, I have not printed this myself yet as I don't have 2 5015 fans to test with, yetOffsets for probe to nozzleX 93.2mmY 6.8mm

This is a vital cable support for the Micro Swiss Direct Drive unit, designed to provide essential stress relief for the cables. To install this bracket, you will need to carefully remove both top wheels and the motor. ... Join our active community...

This is a little kit I designed to store spare parts for my Micro Swiss hotend.Parts stored: Heat break, Heat Sink/parts, and NozzlesI use 0.6 and 0.4 so I have those labeled.I've been using this kit to know when/if I need to re-order something.

ce gabarit permet de centrer le perçage des fixations du mgn12 sur micro swiss direct drive aucun filetage les 4 trous servent a centrer le perçage de la pièce, qui est elle taraudée. ... il vaut mieux percer à 2.5, puis passer à 3mm

This is a little kit I designed to store spare parts for my Micro Swiss hotend.Parts stored: Heat break, Heat Sink/parts, and NozzlesI use 0.6 and 0.4 so I have those labeled.I've been using this kit to know when/if I need to re-order something.

This is a remix of the Micro-Swiss model which retains all of the critical geometry, but greatly simplifies the model by removing the fillets. This is meant to serve as a starting point for further customization without having to deal with the...

BL Touch bracket for Ender 6 with Micro Swiss NG direct drive extruder. Clears printer belt brackets. Uses M3 screws and nuts. Probe offset: M851 X-48.00 Y15.00 Z-4.10 Credit to DevDav I used his back plate to build off of.

Quick tweak of this handy knob to free up the extruder lever on the Micro Swiss Direct Drive Kit. Step file available. Modifications: Trimmed down the shaft to give the clamping lever plenty of clearance. ...Smoothed out the shaft's taper for a more...

A little piece to install the Micro Swiss hotend designed for Cr-10 in to a cr-5 pro carriage. Works fine with the original screws. ... IMPORTANT: You don't need an adapter if you use the CR-10s PRO model!

You need a Micro Swiss clone for your Creality CR10s Pro. ...To assemble it, you'll require the following parts: * 2 x M3 x 20 screws * 4 x M3 x 14-16 screws (for Fan 1) * 1 x M3 x 16-18 screw (for Fan 2 above) * 1 x M3 x 20-23 screw (for Fan 2 below) ...

... ...I am printing templates for my work and during this time I have made 2 upgrades a year ago I installed the Direct Extruder of Micro Swiss and 10 days ago I decided to change the movement of the axles from wheels to 12 mm rails with MGN12H carriage.

I love the look of pixel2's extruder knob, but as designed it does not fit the Micro Swiss extruder I installed on my Ender 5 Plus as the “stem” part is too thick and is obstructed by the tension gear pivot. I did this very simple remix to make it...

This is a linear rail mount for the X axis of the Creality Ender 5 with a Micro Swiss Driect Drive kit. The linear rail used is a MGN12H, 300mm The advantages of this design vs the others are * You don't lose X/Y space * Compatible with...