micro swiss hot end 3d models

When installing the Micro Swiss hot end upgrade, the manual specifies a precise height of 1.7mm protruding from the cooling block. To simplify the setting process, I designed a straightforward jig that covers the top for easy visualization. In my...

I needed a way of connecting a cable chain to my micro swiss hot end. It is a very simple wrap around device that works with Slim X Axis Cable Chain with Extruder and Hotend Mount for Ender 3 Pro by norp April 27, 2020. I used bits of the hot end...

This is a spacer for using the Creality Ender 3 V2 BLTouch kit with an all metal Micro Swiss hot end. The Micro Swiss sits a bit lower than the standard hot end. ... Z-Offset of -2.08 worked for me on my machine with this spacer.

This part helps correct the x axis limit switch get triggered by the hot end carriage at about the right point when using the micro swiss direct drive conversion on the ender 3. ...Designed in tinkercad, include a small nub on the inside to help keep it...

Combined a quick-change base with a base plate for a fang mount that will accommodate a Micro Swiss Hot-end You will need to use 3mm inserts or change hole size to thread them, but with the load of a swiss hot end i would use the inserts. ...I added a...

I then imported the micro swiss hot end and fans from Grab Cad. I recommend a draft shield if an enclosure isn't available. Supports are modeled into the STL. I printed this at 35mm/s, .4 layer height, 20% infil, 4 walls, 260* nozzle temp,...

This base is designed specifically for the micro swiss hot end. To assemble this mount, you'll need to print the fan and 40mm fan duct from https://www.thingiverse.com/thing:2763931. I ended up needing t m3 nuts as spacers for the bltouch; I added...

This is a remix of a remix of the fan duct, that will fit better (not perfect) if you have a micro swiss hot end installed. I'm not an expert (first remix) i took the existing model, i've put it in fusion 360, cut it in half and added 3mm on the Z...

I modified the Micro-Swiss Hot End fan duct for the Fang to allow for more airflow through the fins and improved cooling, so I cut a vent into each side of the heat sink to prevent it from blocking airflow entirely. There are two versions available...

I noticed that the Micro-Swiss Hot End version of the fan duct blocks the sides of the heat sink almost entirely, so I opened a vent in the side to allow more airflow through the fins and better cooling. There are two versions available - one is the...

This is a modular cooler for the CR-10 with a Micro Swiss hot end that combines functionality with ease of use. Both fan mounts are installed without screws, allowing for quick removal for maintenance on the hot end. To install the hot end cooler,...

I recently picked up a Micro Swiss 300c Hot End, and the mount I had been using on the stock hot end no longer fits properly. I modified the STL file in Tinkercad to get a snug fit that works for me. If you experience any problems with this design,...

Seems stable enough without the extra screw Fang mount for Micro Swiss Direct Drive This base is for the micro swiss hot end You will need to print the fan and 40mm fan duct from https://www.thingiverse.com/thing:2763931 I ended up needing t m3 nuts...

I acquired a Micro-Swiss Creality hot end (the all-metal version), and fitted it with a Volcano heater block and nozzle. All components thread together seamlessly, creating a secure seal. A thermal image showcases the temperature gradient during a...

Update: Option 1: Choose from two Micro Swiss hot ends - one with a cable tie for the bowden tube, the other without. Option 2: Select the standard hot end option. Option 3: Opt for the Hero Me stock hot end, available at a 45-degree angle. I...

I'm printing with the Duplicator I3 V2.1, using a Micro Swiss hot end. I designed this back plate with very high tolerances in mind - just 0.5mm between the main body and the drive gear. I've also built in more spring tension, so there's no need to...

Revised for enhanced performance of Micro Swiss hot end silicone technology.

A modified version of frankybuilds' bracket was used, which required some tweaking to work with the Micro Swiss hot end. Frankybuilds' bracket can be found on Thingiverse at https://www.thingiverse.com/thing:3419869, and includes additional parts...

Main Features: Hero Me Gen5 Base Does not go behind the hotend so it can be removed without removing the hotend Does not cover the left belt hook, so belts can be attached after everything has been installed on gantry Tunnel for the Micro Swiss hot...

The BLT mount has a slot to accommodate vertical adjustment, but if laid with the connector resting on the fan, Z offset is around the -0.36 mark when using the the micro-swiss hot-end and nozzle. If you prefer more clearance between nozzle and bed...

This part is only here to help the people that are printing the duct this is a "remix" of and cant use it because micro swiss changed hot end designs. *note* I made this a long time ago and it is NOT perfect. But with a print or two I think this...

The BLT mount has a slot to accommodate vertical adjustment, but if laid with the connector resting on the fan, Z offset is around the -0.36 mark when using the the micro-swiss hot-end and nozzle. If you prefer more clearance between nozzle and bed...

The BLT mount has a slot to accommodate vertical adjustment, but if laid with the connector resting on the fan, Z offset is around the -0.36 mark when using the the micro-swiss hot-end and nozzle. If you prefer more clearance between nozzle and bed...

----------------------------------------------------------------- Hot End Carriage from Micro Swiss - STL and Step Files Unlocked Micro Swiss has generously provided the necessary data to facilitate modifications to various mounts. ...Using Fusion 360,...

... 300x300. ...it's abit more too the back since the bed cannot go completely to the end. Most importantly it's 300x300 again. Check my other designs for the Y endstop. Printer: Creality Cr-10s pro v2 Mod: Micro swiss direct drive extruder with hotend

It's designed for the Ender 3 or Ender 3 Pro with the printermods.com direct drive mod featuring an all-metal Swiss hotend and a BLTouch. I printed this remix using supports and 50% infill at .16mm layer thickness. Due to the direct drive mod, I...

... mounting solution for hero me gen 5 base and a fan guard ;) printed with ABS but can print this with PLA and PETG also. I will post another hero me base later cause the buttom end was little to close to the hot end that I was comfertibal with

Fan housing for Micro Swiss for linear rail

Fan housing for Micro Swiss for linear rail

... ... This moves the Y endstop 6.5mm to truly allign the bed. I also added X-Y-Z since i always forget that... NO MORE! Check my other designs for the X endstop. Printer: Creality Cr-10s pro v2 Mod: Micro swiss direct drive extruder with hotend