micro swiss hot end 3d models

I'd been relying on _3DDP_'s fan ring with my Ender 3 Pro, but after acquiring and installing a new Micro Swiss all-metal hot-end, the existing fan ring was no longer compatible due to the different offset of the nozzle. I transferred _3DDP_'s design...

I'm using the CR-10S Micro Swiss all-metal hot end, so my design fits this hot end specifically. If needed, I can also design one for the stock Creality hot end. Right now, I'm testing this bracket to see if it helps prevent clogging, and logically,...

This remix amplifies LDG92's refined fan duct design, tailored specifically for the standard Tevo Tornado fan configuration. ...By elongating the duct by 3mm, it accommodates the added length of the Micro Swiss all-metal hotend with precision.

Remixed https://www.thingiverse.com/thing:4131344 to fit a Micro Swiss hotend for my Longer LK4 Pro. All I did was widen the opening to fit. ... Just follow the same printing suggestions from the original version.

I upgraded to the Micro-Swiss Direct Drive and was looking for a simple cable management for the hot end. It uses the two extra holes on the right side of the new carriage, The screws are M3 X 6 already tapped in the new carriage. Please let me...

I didn't want to lengthen any cables so I borrowed from Eric's design and added a few bits of my own. It works well. ... PS: This was installed on an ender 3 v2 which has different cable routing than an ender 3.

MicroSwiss Direct Drive Cooler (duel fan part cooling) With BL Touch For Ender 3 V2. This is a slightly modified version of my other cooler that now includes the mount for the BL Touch. This was included after some feedback asking for it to be...

This fan duct is for the Sunlu S8 using the taller Micro Swiss all metal hot end for the CR-10 (https://store.micro-swiss.com/collections/all-metal-hotend-kits/products/all-metal-hotend-kit-for-cr-10-pro). I have also added an attachment for a 3D...

Just a small change I did where a fan grill is used and because of that the fan are screwed in using m4-screws. ...I use a 20mm thick 40mm fan and use m4x24mm screws.

Obviously this design is subject to the whims of Micro-Swiss, so it shouldn't be used for cloning their, only customizing around it. Remixes: https://www.thingiverse.com/thing:4170190 -> Not actually remixed from here, I found this model...

Update: A revised edition has been integrated, featuring a 7.5 mm offset modification to ensure seamless compatibility with the CR10 Pro. ... A modified iteration has been crafted, seamlessly accommodating the Micro Swiss all-metal hot end.

Decided to make a cooler that fits directly to the Micro Swiss DD bracket as I wasn't happy with the other designs I found. Bigger cooling nozzles in prototypes allow for the part cooling to flow and not have as much static pressure. Didn't do...

It's possible that all I needed to do was raise the temperature or change some settings, but I bought a Micro Swiss hot end, found it to be 5.3 mm too short, modified the part that this design is based on and have since gone through several rolls of...

I swapped out my hot end with a Micro-Swiss all-metal hotend. The micro-swiss doesn't have one of the necessary attachment holes, so I designed this to fit both mounting holes in the hotend attachment plate. This duct does not include the BL Touch...

I recently decided to upgrade my part fan on my cr-10 by installing a 40x40 noctua fan, which I had previously used and enjoyed with the EPF Fang for Micro Swiss all metal hot end designed by Metalurgia. To adapt it for use with a 40x40 part fan, I...

Being upset with the stock hot end ([Poor heat sink cooling (wrong placement of heat sink respect to blower fan), unreliable thermister security (the thermistor is just being held by the silicon sock, E0 errors), unstable heat block (lossen heat...

A hot end bracket for the Micro Swiss Direct drive to attach cable/drag chain to on Ender 3/pro 3d printers. ...it works well with no loss of travel in the X axis

It is possible that this fan shroud could be used without the Micro Swiss hot end. The only concern is that the BLTouch may be mounted too low for the stock hot end. You may need to file / sand / machine down the bottom of the BLTouch mount to...

Being upset with the stock hot end ([Poor heat sink cooling (wrong placement of heat sink with respect to blower fan), unreliable thermistor security (the thermistor is just being held by the silicon sock, E0 errors), unstable heat block (loosen...

**Petsfang Titan Direct for Alfawise U10** ***** Following the success of the Petsfang Direct for CR10 and Tevo Tornado, I have created a mod for the Alfawise U10. The installation process is straightforward and easy to follow. This mod works...

Moved the 3d touch/BL touch out 5mm so you can fit other way round

This is a Modified part for the Qidi X-Plus printer, To accommodate the changes that occur when you upgrade to the ***Extended*** Micro-Swiss MK10 All-Metal Hot-End kit. This is specifically for the Kit which uses a 22.35mm Thermal Tube, Not the...

Modified to work better with 20mm thick fans, thermistors with nuts, Micro-Swiss Direct Drive, and the Creality metal BLTouch bracket. Closes up gaps and adds plenty of room for wiring. This also fixes the positioning of the stock part cooling fan...

Additional mounting bracket and accessories for brush cleaning wheels now available on Thingiverse, compatible with Petsfang Titan Direct Micro Swiss and Stock CR10 & Tevo Tornado hot ends. Visit https://www.thingiverse.com/thing:2907538 to explore...

List of files to print for specific printers and hot ends at: http://www.dpetsel.com/files2print-titan-direct.html FILES 2 PRINT TITAN Direct TORNADO FILES...

Built-in recesses for the M3 nuts (5.5mm wide across the flats) -includes optional add-on part that goes under the hot end fan to complete the duct to get absolute maximum efficiency. leaving this as a separate part from the fang because it would...

Fan shroud to add dual 5015 blower fans to Ender 3 V2 with Micro Swiss Hot End and CR Touch.

Redesigned this to fit a Creality CR10S Pro V2 with a Micro Swiss hot end and direct drive. Used supports on build plate only. ... Updated with correct duct, and no longer need to resize.

It attaches to the Micro Swiss hot end to give a more accurate reading of the resonance frequencies at the extruder tip. Requires 4x m3 screws, either 4mm or 5mm. Might fit on other hotends, but might require some tweaking to fit. ...Remove hot...

Despite having no prior experience with Tinkercad, I decided to try modifying it for the Micro Swiss hot end. The initial designer deserves all credit for their work. My contribution was merely extending the bracket in a somewhat crude manner. ...The...