micro swiss extruder ender 3 3d models

Remix of Ender 5 Plus Micro Swiss NG Cable Strain Relief by Tuna on Printables. Original was slightly too thick to use with the CR-10/Ender3 NG variant and would cause binding of the V rollers. Rather than thin it out, potentially losing some...

This is an Apogee shroud modification for an "Ender-3 V2 Neo" with a "Micro Swiss hotend" (not usable with the original Neo hotend). Unlike the original Apogee shroud, this modification leaves the CR-Touch mount on the left side. This also means...

I have made changes to make it fit the Micro-Swiss Ender 3 direct drive hot end setup for my Ender 3 V2 since the original shroud does not fit the bracket. There are few other minor tweaks and optimizations I've done on top of the original AYF...

Love this design not just for the clean look, but also for the compact size and weight which is fairly important for direct drive setups.I have made changes to make it fit the Micro-Swiss Ender 3 direct drive hot end setup for my Ender 3 V2 since the...

Love this design not just for the clean look, but also for the compact size and weight which is fairly important for direct drive setups.I have made changes to make it fit the Micro-Swiss Ender 3 direct drive hot end setup for my Ender 3 V2 since the...

[UPDATE: January 29, 2021] I remodelled the x-axis cover part so that the endstop cable is not squeezed between endstop housing and strain relief This is a re-mix of the cable management for Micro Swiss DD from FastIndy...

Hobbled together something that will work to properly allow the NG extruder to hit the X-Axis limit switch on the Ender 3 V2 Neo from Creality. ...The switch style is that of the Ender 3 S-1 model which lays flat instead of vertical.

After adding a Micro Swiss direct drive to my Ender 3 I decided to also upgrade the wiring by adding drag chains to all three axes. I'm going to warn you up front that the stock wiring harness was not long enough for these chains on my printed. ...

This is a simple design to be able to install the hot end fan and the part fan on a new Micro Swiss Direct Drive. Since the original hard ware will not fit the new part, here is a solution. ... Just change the parts Fan Nozzle 4 mm and centered with the...

This is a remix of a remix of the fan duct, that will fit better (not perfect) if you have a micro swiss hot end installed. I'm not an expert (first remix) i took the existing model, i've put it in fusion 360, cut it in half and added 3mm on the Z...

The answer is yes, if you use Micro Swiss' direct extruder along with the cable strain relief from Sergentchat https://www.thingiverse.com/thing:4591387 (scale it down to 10 %). Then you will need a long shaft, to avoid collision with the strain...

Decided to make a cooler that fits directly to the Micro Swiss DD bracket as I wasn't happy with the other designs I found. Bigger cooling nozzles in prototypes allow for the part cooling to flow and not have as much static pressure. Didn't do...

... This makes for a better mesh in my opinion and it just looks cool. 3. Designed a new mount for the BTT Smart Filament Sensor. 4. ...Redesigned the top hat to accommodate the wiring harness a bit better with the addition of all the extra stuff.

this is a remix from Anycubic Vyper / Filament Sensor, Cable Holder, Bearing 608 by kiteboarder1980... ...adapted version with different holes for recessed screws. so the screws from the original extruder can be used

<p>Fitts with the driveinator (direct drive). If you only print wth pla the fan shroud can be printed in pla. ...If you have an anclosure you will need to print it in pla or abs.</p>

Fan Shroud, Probe Brackets and Endstop Bracket STL files For Micro Swiss NG Extruder for Ender-5, Ender-5 Pro and Ender-5 Plus. Compatible with: SKU: M3202 (Standard V-Roller Edition) SKU: M3204 (Linear Rail Edition) Use support from...

This spacer/bracket is to move the filament sensor so that it can be used with the Micro Swiss Dual Gear extruder on an Ender 5 plus/pro. Use 2 M3x8 screws to mount the spacer to the stock bracket. And 2 M3x20 screws and nuts to mount the...

I tried looking for parts to add a 10x20mm cable chain to my Ender 5 Pro with a Micro Swiss Direct Drive Extruder with the Exoslide Linear Slide Kit. Here is the 10x20mm Cable Chain I used, https://a.co/d/iSzwFDn There are little rectangular...

Since I upgraded my Ender 5 with Micro Swiss Direct Drive and Satsana duct I've been looking for a perfect extruder knob. I tried many knobs but wasn't really happy with any of them. I really liked this oversized design by caganseval...

I ended up getting the Micro Swiss Dual Gear Extruder and saw that I needed to print a part in order for the filament to line up from the run out sensor on the Ender 5 plus. I couldn't find one so I had to make one. This is a very simple design...

The bracket that's included with the Micro Swiss Direct Drive Extruder for Creality CR-10 / Ender 3 Printers.

... loom from rubbing my enclosure lid. ...I tried printing the chain links, but they eventually failed. You can just get some R18 10x15 cable chain from Amazon or a local 3D print shop.This design uses the mounts with 3 holes per. ...I used M3 hardware.

Remixed to match the mount of the Micro Swiss Direct Drive Extruder for Creality CR-10 / Ender 3 Printers. https://store.micro-swiss.com/products/micro-swiss-direct-drive-extruder Nice and secure mounting under the heat brake, I applied a dab of...

Ender 3 3 Pro Top Filament Guide for Direct Drive Extrusion with Micro Swiss System 1. Install Guide: Attach the Top Filament Guide to the right side of your 3D printer's extruder system. Secure it firmly using M5x10 screws provided. 2. Cable...

Fan Shroud Adapter and PTFE Guide Tube Bracket used to install the Micro Swiss Direct Drive Extruder kit on an Ender 3 Max. ... The PTFE bracket will align the PTFE tube with the Ender 3 Max filament runout sensor.

I love the look of pixel2's extruder knob, but as designed it does not fit the Micro Swiss extruder I installed on my Ender 5 Plus as the “stem” part is too thick and is obstructed by the tension gear pivot. I did this very simple remix to make it...

Ender 3 V2 Neo X-Limit Switch Housing for Micro Swiss NG

Shifted a bit to each side to make room for the Micro Swiss extruder instead of stock

It is a remix of https://www.thingiverse.com/thing:4369859 to fit Micro-Swiss Direct Drive for Ender 3 Pro. ... Offset for my extruder: X-49.8 Y-09.3 Z-2.80

Simpler Knauf for Micro Swiss Direct Extruder with Direction Indication, since this works in reverse to the normal Extruder. ...Printed with the following Settings: Layer Height 0.12mm Filling Lines 20% Material PETG Gray (Amazon)